WORX 20V Big Foot (Green) Lithium Battery Holder V2 (Power tap, Wall mount, Stackable, Protection), perfect fit and super smooth

威克士20V大脚（绿色）锂电池支架 V2（取电、壁挂、堆叠、保护），完美匹配且超丝滑
Worx 20V Big Foot (Green) Lithium Battery Holder V2 (Power Supply, Wall-Holder, Stackable, Protective), Perfect Fit and Ultra Smooth

Previously, I released version V1 (measured based on the orange 20V), and found that everyone quite liked it. Recently, I made a cyclone vacuum cleaner and planned to use the green Bigfoot Worx battery as the power source. In actual use, I found that the previous design had some unreasonable aspects, the dimensions were not precise enough, and the connection was not smooth. So, I redesigned this V2 version, which only supports the green version battery (it seems that Worx has phased out the orange version). I also carefully tested and tried my three versions (2018 31002465, 20190400334558, 20241200708235). Although all three versions have slight dimensional differences, using the V2 version holder provides excellent fitting and smooth handling (once the plug pins are installed; otherwise, the early versions may wobble slightly).

I hope the new version will be to your liking. If you find it practical and easy to use after trying, please give me a boost. Thank you.

If you are looking for the Worx 20V (orange) lithium battery holder, please click the link to go there.

Main functions:
1. Supports only Worx 20V Bigfoot (green) lithium batteries
2. Access electrical energy and use the battery as a 20V power source
3. Provides wall-holder holes (two M4 countersunk holes) for easy wall holdering or, with some modifications, on a pegboard
4. Can be connected to other device enclosures through wall-holder holes to become part of a device
5. The top becomes flat after installing the holder, allowing for stackable storage
6. Offers some protection to the battery's interface

Notice:
1. You need to prepare your own copper connector pins (recommended methods are described below) and solder wires to the rear of the pins
2. Use high-current-capacity copper cables for soldered wires, at least 1.5 mm², preferably 2.5 mm², to make the most of the battery’s power
3. Once the connector pins are installed in the pin holder with wires, they fit tightly into the holder body and won't easily slip out; using a little glue will make it more secure
4. This holder has been tested on three Bigfoot batteries and works well, but it does not guarantee compatibility with all current or future Worx Bigfoot batteries
5. The pins can be sourced from broken appliance plugs, outdated low-power chargers, etc., but this requires some DIY skills
6. The author provides a separate blank pin holder model (see print configuration list) that you can customize according to the shape of your pins for use
7. Safety precautions should be observed when using lithium batteries—prevent short circuits, avoid excessive power, and prevent fire hazards

Author-recommended method for obtaining copper power supply pins:

1. Purchase the socket, link: Black fixed two-prong plug (Type A plug), Type B plug is the three-prong plug available under this link.
2. Operate as shown in the picture below (using Type A plug as an example):

Original models list:

Drill Bits, Blades Anti-Puncture Storage Box - [20260703] ★★★

Worx 20V BigFoot (Green) Lithium Battery Holder V2 V2 - [20251228] ★★★★

Pencil Case[Screwless,Roll-up] - [20251019] ★★★

A1 mini TPU special top spool holder - [20250808] ★★★★

LED Lamp-MH001 Ultra Practical Component - [20250701] ★★★★

Wired battery compartment (with lid):18650，21700 - [20250629] ★★★

Potentiometer knob (6mm fit) - [20250401] ★★★★

Rotary shaft with Automatic rewinding:AMS lite，A1，A1 mini- [20240412] ★★★★★

A1 / A1 mini fan Cover Guard - [20240226] ★★★★

AMS Lite Large diameter spool adapter - [20231127] ★★★

see more original model…

see more original model…