A10 Kit Card by planes01

planes01

Hobby & DIY>Vehicles

Print Profile(5)

All

P1P

P1S

X1 Carbon

X1E

Kit With Frame (4 color) -- 0.2mm layer, 2 walls, 15% infill

Designer

4.4 h

1 plate

4.9(13)

Kit No Frame (4 color) -- 0.2mm layer, 2 walls, 15% infill

Designer

4.4 h

1 plate

5.0(9)

Kit With Frame (3 Color) -- 0.2mm layer, 2 walls, 15% infill

Designer

4.2 h

1 plate

4.8(5)

Kit With Frame (Small Size 1 Color)

Designer

1.7 h

1 plate

4.3(8)

Click to see more

Boost

363

613

463

268

Released

Description

Overview

A-10 Kit Card upgraded to 3D fuselage format

Check out the SR-71, B-52, A-10, 787, and Darkstar!

Check out the full airplane kit card collection → linked here!

Profiles

Kit With Frame
- plane in a kit card format ideal for gifting to others
Kit No Frame
- plane without a kit frame ideal for assembly right off the printer

Filament

As shown:

eSun PLA+ Gray
Hatchbox PLA Gray
Bambu Lab PLA Black

Tips

Model requires close tolerances to ensure snug but not tight or loose fit
- Make sure the model cools to room temperature before assembly
- Ensure filament is properly calibrated with no excessive over extrusion
- If there is some over extrusion the parts may need to be lightly sanded at interfaces for fitment
Ensure good bed adhesion
- Make sure printer is fully calibrated
- Make sure print bed is clean & dry (soapy water is my favorite for cleaning - simple & works)
- Make sure filament is dry (wet filament can generate non-continuous flow that can cause bed adhesion issues)
- Cooling & Temps - make sure they are correct for your printer, build plate, and filament
- Smooth PEI plate is recommended

Assembly

Remove all pieces from the kit
Debur as needed to smooth edges
Insert wing into forward fuselage slot
Insert horizontal tail into aft fuselage slot
Insert engine pylon into fuselage
Insert engine into engine pylon
Insert missiles into wing
Place airplane onto stand
Enjoy!

Snap into place design

Comment & Rating (78)

@user_1527158710

Boosted

Love all your stuff. I was wondering if you plan to get into helicopters as well?

The designer has replied

@planes01

Hey! Thanks for all of your support. Helicopters would be great. Do you have one in mind that you are interested in?

@pumpkin20303

Replying to @planes01 :

The Tiger helicopter from 007 Golden Eye movie :)

@user_675958928

Replying to @pumpkin20303 :

bell uh i d ^^

@s.toni

Boosted

I have to glue it

The designer has replied

@s.toni

Boosted

can you give me a tip

@planes01

insert the pylon into the wing slot and push it all the way to the back. then press down on the front. it will snap into place with a little force.

@s.toni

Boosted

I will try it on the next print thank you 🙂

@Big.Daddy.

Boosted

Print Profile

Kit With Frame (4 color) -- 0.2mm layer, 2 walls, 15% infill

came out good thanks for sharing

The designer has replied

@planes01

thanks for sharing! I love the green! what specific filament colors did you use? would love to print one like that myself!

@Big.Daddy.

Boosted

Replying to @planes01 :

numakers grass green

@Big.Daddy.

Boosted

Replying to @planes01 :

All Numakers filament Dark grey, light grey, black, and grass green like there filament and its 13.99 1k rolls if you buy 10 rolls

@Tokolozi

Print Profile

Kit No Frame (4 color) -- 0.2mm layer, 2 walls, 15% infill

So glad you made a 3D hull version of the A10! Fits nicely in the collection...

The designer has replied

@planes01

love that display

(Edited)

@DJMOJO

Print Profile

Kit With Frame (4 color) -- 0.2mm layer, 2 walls, 15% infill

printed well!

The designer has replied

@planes01

thanks for the feedback!

(Edited)

@Factory3d

Print Profile

Kit With Frame (3 Color) -- 0.2mm layer, 2 walls, 15% infill

Love the design but it is a nightmare to assemble!

(Edited)

The designer has replied

@planes01

what was challenging? the image shows all major pieces together.

@Factory3d

Replying to @planes01 :

Well the engines, and the missiles were very though to assemble, maybe i should have try PETG... Also the wings and back tail are hard to center. Other than this i love what you make!

@Mitch23

Print Profile

Kit No Frame (4 color) -- 0.2mm layer, 2 walls, 15% infill

love the A10 Thanks!

@RicheyAvengers

Print Profile

Kit With Frame (4 color) -- 0.2mm layer, 2 walls, 15% infill

instruction are a little unclear but it looks great

@PaNTerA

Print Profile

Kit With Frame (4 color) -- 0.2mm layer, 2 walls, 15% infill

The designer has replied

@planes01

thanks for sharing your awesome print! looks great!

(Edited)

@dimas_kherson

Print Profile

Kit With Frame (4 color) -- 0.2mm layer, 2 walls, 15% infill

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.