787 Kit Card

Copyright Claim

787 Kit Card

Boost
343
545
44

Print Profile(3)

All
P1P
P1S
X1
X1 Carbon
X1E
A1
A1 mini

Kit with Frame -- 0.2mm layer, 2 walls, 20% infill
Kit with Frame -- 0.2mm layer, 2 walls, 20% infill
Designer
3.7 h
1 plate
4.8(23)

Kit no Frame -- 0.2mm layer, 2 walls, 20% infill
Kit no Frame -- 0.2mm layer, 2 walls, 20% infill
Designer
3.5 h
1 plate
5.0(9)

A1 Mini, One Plate, No Frame
A1 Mini, One Plate, No Frame
3.8 h
1 plate
5.0(2)

Boost
343
545
44
15
757
303
Released

Description

Overview

787 kit card

 

Check out the SR-71, B-52, A-10, 787, and Darkstar!

Check out the full airplane kit card collection → linked here!

Profiles

  • Kit With Frame
    • plane in a kit card format ideal for gifting to others
  • Kit No Frame
    • plane without a kit frame ideal for assembly right off the printer

Filament

As shown:

  • eSun PLA+ Cold White
  • Inland PLA Gray
  • Inland Egyptian Blue
  • Bambu Lab PLA Black

Tips

  • Model requires close tolerances to ensure snug but not tight or loose fit
    • Make sure the model cools to room temperature before assembly
    • Ensure filament is properly calibrated with no excessive over extrusion
  • Ensure good bed adhesion
    • Make sure printer is fully calibrated
    • Make sure print bed is clean & dry (soapy water is my favorite for cleaning - simple & works)
    • Make sure filament is dry (wet filament can generate non-continuous flow that can cause bed adhesion issues)
    • Cooling & Temps - make sure they are correct for your printer, build plate, and filament

Assembly

  • Remove all pieces from the kit
  • Debur as needed to smooth edges
  • Insert wing into forward fuselage slot
  • Insert horizontal tail into aft fuselage slot
  • Insert engine to wing
    • Recommend aft end first, then press down on the forward eng. It will clip into place. (See gift below)
  • Place airplane onto stand
  • Enjoy!

 

 

Comment & Rating (44)

Please fill in your opinion
(0/5000)

Print Profile
Kit no Frame -- 0.2mm layer, 2 walls, 20% infill
nice profile. printed mine in dual color blue/white
The designer has replied
1
Reply
looks fantastic! thanks for sharing!
0
Reply
Print Profile
Kit with Frame -- 0.2mm layer, 2 walls, 20% infill
Another nice model. My son put it together right away. Thank you.
The designer has replied
1
Reply
thanks for sharing your awesome print!
(Edited)
1
Reply
Print Profile
Kit no Frame -- 0.2mm layer, 2 walls, 20% infill
Printed great
1
Reply
Print Profile
Kit no Frame -- 0.2mm layer, 2 walls, 20% infill
The profile with the frame was too big for my A1 mini. this profile with a little bit of shifting to avoid. illusion with the prime tower worked perfectly
1
Reply
Print Profile
Kit no Frame -- 0.2mm layer, 2 walls, 20% infill
100% and 50% perfect prints
0
Reply
Boosted
Very nice!
0
Reply
Boosted
Print Profile
Kit no Frame -- 0.2mm layer, 2 walls, 20% infill
1
Reply
another great model!!! You should do a F-18C!
The designer has replied
1
Reply
It's in work!
2
Reply
Print Profile
Kit with Frame -- 0.2mm layer, 2 walls, 20% infill
Perfect print. Nice tight fit for all parts. Only glue necessary was on the engine. Thank you, printed it for a retiring pilot.
1
Reply
Print Profile
Kit with Frame -- 0.2mm layer, 2 walls, 20% infill
thank you,. nice
1
Reply

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.