X1C Remix for AMS Riser Remix by maCyo42 Remixed by maCyo42

Remixed by

maCyo42

3D Printer>3D Printer Accessories

Print Profile(2)

All

P1S

P1P

X1 Carbon

X1E

0.12mm layer, 2 walls, 20% infill

Designer

6.4 h

3 plates

4.7(82)

TPU Button Inserts @0.16mm layer, 4 walls, 15% infill

Designer

15 min

1 plate

4.8(22)

Open in Bambu Studio

Boost

198

464

144

1.5 k

1.1 k

Released

Description

NEW AMS Riser V2 is released

This is the X1C Front Dash Remix for my AMS Riser Remix by maCyo42 that Supports Full COB Led Strip, a second Build Plate Slot an many other improvements like Spool Holder Left and Right.

IMPORTANT
i haven´t printed the X1C Version but the P1S Version is nearly the same. Please keep this in mind if you want to print this Version.
It would be nice if someone who want to print this Comment with an Make incl. Picture after printing.

You need the Parts of https://makerworld.com/de/models/38916#profileId-37794 to complete the Project except of the P1S Front Dash Parts.

happy printing

Comment & Rating (144)

@dgauche

Print Profile

0.12mm layer, 2 walls, 20% infill

Did not like the text, so I removed it.

@apt3d

I feel the same way. Mind if I ask, what you did to remover them? Did you have to remix it? Thanks and love the colors! I was going to do the grey and then wasn’t sure what other color to choose, but the black does look good.

@dgauche

Replying to @apt3d :

I just use the color fill if I recall correctly.

@user_462577701

Hi, I might miss someting here. How do the printed buttons push the actual buttons? is there a TPU part I'm missing? The rim of the printed buttons is wider than the actual buttons. Thanks in advance!

(Edited)

The designer has replied

@user_462577701

Found it in the original files

@maCyo42

Replying to @user_462577701 :

thank you for the Feedback. 😊👍

@nixdesignworksh

Replying to @user_462577701 :

Where are these button inserts I don't see them on any of the files, am I missing something. thanks

@ryan.binnie

not too sure where I went wrong but this is PETG on the first quartile of it, any tips / thoughts?

The designer has replied

@maCyo42

Filament drying nozzle change flow calibration ...

@ryan.binnie

Replying to @maCyo42 :

I've tried all of these funny enough, its a speed issue, think I have something in the settings making it go wrong, because when I put it on the slow 50% speed it prints perfectly

@7Kitty7

Replying to @ryan.binnie :

@ryan.binnie I also would like to print this in PETG, like you did. Could I please ask what material you used for the supports - or did you just print everything in PETG then cut out the supports/ sand down the rough edges? Thank you.

@metical

Model prints great and works fine for X1C. I’m still figuring out how to install the buttons. Looks like there are separate inserts that I need to print which I don’t think we’re in the model file. The outer part of the button does seem hard to squeeze into the hole though. Haven’t fully inserted yet until I print those inserts. Thanks again for the remix!

@Chris.henle

its hard for me too to Push the Button holder inside…is there a Trick ? or just violence ?😂

@EngineeringProj

Whats filament is this?

@Aletheia

Replying to @Chris.henle :

I just removed a little from the edges with a deburring tool, and it goes in snug after.

@jasonrfreeland

Print Profile

0.12mm layer, 2 walls, 20% infill

Came out nicely in PLA Tough and PLA-CF.

@nnamrakk

Print Profile

0.12mm layer, 2 walls, 20% infill

Perfect fit for the x1c.

(Edited)

@Mal86

Print Profile

0.12mm layer, 2 walls, 20% infill

I put both pieces on one plate. Not sure why they were on two.

@AMac67

Print Profile

0.12mm layer, 2 walls, 20% infill

These fit perfectly with the main parts that I printed with PETG. I printed these with PLA as I wanted to print them quick and they came out perfect. The reason the buttons aren't installed is I am printing the inserts today.