Balloon Powered Toy Car
Copyright Claim
Balloon Powered Toy Car
Boost
272
495
132
GIF
Print Profile(4)
R02 - more ground clearance, 0.2mm layer, 2 walls, 10% infill
Designer
1.1 h
1 plate
R02A - single color more ground clearance, 0.2mm layer, 2 walls, 10% infill
Designer
37 min
1 plate
R02 for A1 Mini, 0.2mm layer, 2 walls, 10% infill
Designer
1.2 h
1 plate
0.2mm layer, 2 walls, 10% infill
1.1 h
1 plate
Boost
272
495
132
2
754
873
Released
Description
Overview
This is a print-in-place balloon powered car that prints in about 60 minutes with multicolor and 40 minutes in single color. Run on smooth surfaces.
- No assembly required
- Use with a 5 inch balloon (amazon link)
Also check out the standard version > LINK
Check out the SR-71, B-52, A-10, 787, and Darkstar!
Tips for Successful Race!
- Print at normal speeds
- Ensure filament is dry to maintain good wheel spin and tolerances
- Balloon must stay upright
- Do not overinflate balloon – 50 to 75% inflation is ideal to keep balloon upright and avoid dragging
- Install balloon and then inflate by blowing through nozzle
- Seal nozzle with finger until ready to race!
- Run on a flat & smooth surface
Profiles
- R01 - Initial release
- R02 - Added 1mm ground clearance
- R02A - Single color variant of R02
Comment & Rating (132)
All
Print Profile
R02 for A1 Mini, 0.2mm layer, 2 walls, 10% infill
Impresión perfecta, se mueven bien las ruedas y con el globo adecuado es bastante rápido. a mi hijo le encanta
The designer has replied
1
Reply
thanks!
0
Reply
Print Profile
R02 - more ground clearance, 0.2mm layer, 2 walls, 10% infill
printed great, just picked up some balloons to give them as a gift.
The designer has replied
1
Reply
awesome! thanks for sharing your print!
0
Reply
Print Profile
R02A - single color more ground clearance, 0.2mm layer, 2 walls, 10% infill
Nice
The designer has replied
1
Reply
thanks!
(Edited)1
Reply
Print Profile
R02 - more ground clearance, 0.2mm layer, 2 walls, 10% infill
very cool toy thanks
The designer has replied
1
Reply
love the orange!
(Edited)2
Reply
Boosted
Print Profile
R02 - more ground clearance, 0.2mm layer, 2 walls, 10% infill
Personalizado, listo para regalar a amigos y familia. Impreso en PLA, solo con un golpe fuerte llega a romperse el eje. Las pruebas con el nombre en ambas caras no han salido tan bien ;D
1
Reply
Print Profile
R02 - more ground clearance, 0.2mm layer, 2 walls, 10% infill
cool design, prints well
1
Reply
Print Profile
R02 for A1 Mini, 0.2mm layer, 2 walls, 10% infill
I like this
(Edited)
1
Reply
Print Profile
R02 for A1 Mini, 0.2mm layer, 2 walls, 10% infill
The wheels rolled freely directly after the print, I still haven't found a ballon to try it fully with.
1
Reply
Print Profile
R02 - more ground clearance, 0.2mm layer, 2 walls, 10% infill
The designer has replied
2
Reply
love the wheels!
(Edited)1
Reply
Print Profile
R01 - initial release, 0.2mm layer, 2 walls, 10% infill
cool
GIF
1
Reply
License
This work is licensed under a Standard Digital File License.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.
Related Models
© 2024 MakerWorld