Bambu lab TPU-HF profiles (Printer and filament)
Remixed by
Copyright Claim
Bambu lab TPU-HF profiles (Printer and filament)
Remixed by
Boost
148
260
159
Print Profile(2)
0.2mm layer, 2 walls, 15% infill
Designer
51 min
1 plate
0.2mm layer, 2 walls, 15% infill
1.3 h
1 plate
Open in Bambu Studio
Boost
148
260
159
7
990
941
Released
Description
I have had great success with this profiles. Both on Bambu lab TPU-HF and some random noname TPU from amazon that actually handles higher speeds.
NOTE: always dry your filament before printing. =)
Overture High Speed TPU is confirmed working with this profile.
Comment & Rating (159)
All
Print Profile
0.2mm layer, 2 walls, 15% infill
prints perfect!
The designer has replied
1
Reply
Nice! What filament is that? :)
0
Reply
Replying to @BjornB
its Eryone TPU transparent
0
Reply
Replying to @alocer
Ah, okay. I gotta get some transparent TPU 🙌
0
Reply
thanks printed great but got some stringing going on. is that temperature issue? TIA
Printed with Giantarm TPU white
(Edited)
The designer has replied
1
Reply
That is most likely a moisture issue. Have you dried it enough? I keep my TPU in the dryer while printing
0
Reply
Replying to @BjornB
I did dried the TPU for 4 hours at 45c prior printing and drying in the dry box at 45c while printing.
total print time is about 1hr30mins.
thanks for the reply.
0
Reply
Replying to @user_2761495612
Increase the temp to 55C for TPU, that's the magic number =)
I always dry TPU for 6 hours at 55C before starting the print, and like you did, i keep it in the dryer while printing
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Tested with Sainsmart TPU
The designer has replied
1
Reply
Seems to be working good! I used Sainsmart colorchanging TPU (goes from orange to yellow when heated above 20C) and it works just fine. But it's important to dry the filament enough before printing to avoid tiny strings
0
Reply
Replying to @BjornB
Ok Ty
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Nice Print 👌 🛥
The designer has replied
1
Reply
Thank you!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Perfect!!
No strings.
You need to dry TPU before printing.
Thank you.
Bamboo TPU 95A HF, by A1 mini.
1
Reply
setting please?
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Printed in TPU. Fun squishy benchi!
(Edited)
The designer has replied
1
Reply
Thanks for the pictures! 🙌
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Printed very well. There was a bit of stringing on the top layers, but that is probably just printer settings that I need to adjust.
The designer has replied
1
Reply
That looks good, except for the strings. You need to dry that more 🙌
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
so cool
The designer has replied
1
Reply
🙌🥳
0
Reply
Boosted
Good profile thank you a lot, especially if we take into account that I printed just out of the bag without drying first. (my filament dryer arrives in two days and I'm kind of impatient hahah) I Use Polymaker TPU95-HF filament on an X1C
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Bambu tpu
1
Reply
This remix is based on
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike
© 2024 MakerWorld