Bambu Lab AMS Helper PTFE Mod Lite

Remixed by

Bambu Lab AMS Helper PTFE Mod Lite

Remixed by
Boost
110
271
59

Print Profile(3)

All
P1P
P1S
X1
X1 Carbon
X1E
A1

Lite Original height, -1 cm, -2 cm.
Lite Original height, -1 cm, -2 cm.
Designer
3.8 h
3 plates
3.8(34)

All types on different plates, 0.20mm layer, 3 walls, 15% infill
All types on different plates, 0.20mm layer, 3 walls, 15% infill
1.3 h
3 plates
4.0(9)

PLA 0.20mm
PLA 0.20mm
30 min
1 plate
1.0(1)

Boost
110
271
59
0
398
318
Released

Description

The original is from dkarjadi .

https://www.printables.com/de/model/613353-bambu-lab-ams-helper

https://makerworld.com/en/models/41406#profileId-41677

 

The remix that I remixed is from Lord Necci

https://www.printables.com/de/model/615737-bambu-lab-ams-helper-ptfe-mod

 

Update: added additional heights, -1 cm height and -2 cm height.

 

My remix has the same problems as the original.

Comment & Rating (59)

Please fill in your opinion
(0/5000)

Print Profile
Lite Original height, -1 cm, -2 cm.
perfect
1
Reply
Print Profile
Lite Original height, -1 cm, -2 cm.
During the initial AMS spool sensing operation, the helper fell off as soon as the filament direction was reversed (respooling). Also, I found the design to be too flexible with the middle material removed. Also, I printed the -1sm version Therefore it did not work at all. Printed on X1C with Bambu PLA Basic
(Edited)
The designer has replied
0
Reply
My remix has the same problems as the original, I haven't found a way to fix it yet. If you have an idea, tell me, I'm open to suggestions.
0
Reply
Print Profile
Lite Original height, -1 cm, -2 cm.
I printed "-1" version. Too high in my oppinion. Comes off while reels turn backword direction so I used double side tape and it works but... For more than 1kg rolled on the reel forget to use this cause filament will rub the back off this helper. Recommend to use flexi plastic then PLA. 1 helper was broken by the printer where reels worked backword.
0
Reply
has anyone else had any issues with the legs for the wall helpers snapping off berceuse of the way the layers are printed, like in my photos below ? im printing them with 100% infill
0
Reply
Print Profile
Lite Original height, -1 cm, -2 cm.
Printed great! Fit right into the ams slots. Time will tell if it helps. Thanks for the print.
0
Reply
Hi do you also experience that the lid doesnt close properly with this installed ?
The designer has replied
0
Reply
Yes, the part presses the filament to the lid, but I can't change that, the original design is from dkarjadi, I just adapted it for myself. Maybe it could be made shorter, but I haven't bothered with that yet.
0
Reply
I shortened it by 1 sm but haven't tested it yet, printer is busy :) The shortened one is under raw model files with -1sm on the filename.
0
Reply
thanks will test the shortend file and let you know. other than that great design and print profile. came out very nice
2
Reply
Print Profile
All types on different plates, 0.20mm layer, 3 walls, 15% infill
0
Reply
When my AMS material gets stuck, the bracket may be pulled off due to excessive tension.
The designer has replied
1
Reply
My remix has the same problems as the original, I haven't found a way to fix it yet. If you have an idea, tell me, I'm open to suggestions.
1
Reply
Doesn’t seem to work if you have silica boxes.
0
Reply
I have edited the original boxes i printed from someone, so they fit.
0
Reply
Print Profile
Lite Original height, -1 cm, -2 cm.
does not fix the spool issue, and does not stay attached. I took these off my AMS after a couple prints.
0
Reply