Dummy13 Goes to the Moon Astronaut Remix kit card

Please keep all these small parts away from children and pets, some parts have pointy ends, and they could be a choking hazard too.  Make or use these models at your own risk.

If you find these for sale on Amazon , Etsy or anywhere else, they are not being sold with my permission. There are no "authorized" sellers of these models. They were made for the 3D printing community, not for Amazon or Etsy sellers to profit from.

5/20/2025: This has been updated to V1.2 with a new helmet design that does not require glue to assemble.

Dummy13 may not have the right stuff to go to the moon, but that's OK, it's a robot (I think). With this astronaut remix, Dummy13 will be ready to be strapped to a rocket for a trip to the moon and beyond. For some reason I included a backpack and a helmet, but don't over think it (I didn't). Maybe the pack is for extra batteries or something? In any case Dummy13 will look just like a real astronaut, while performing those dangerous one way missions to places humans dare not go.

This is a single color printer friendly remix, of my multicolor Dummy 13 Astronaut suit. It's also of course, a remix of Lucky13 Toys' awesome Dummy 13 v1.0 model (note that this should be made with the v1.0 models and not the beta design).  All the parts are now available on a card, which includes all the armor parts (so just grab the frame parts from the Dummy 13 model to have everything needed).  

This single color version includes a helmet with a separate visor (and optional stripe). Since it's split, the helmet can be printed in different colors and assembled.  With the v1.2 update, glue is not required to assemble the helmet, since the stripe and visor snap into place.  To install the visor, carefully remove any sprues and then it can slide into place.  It should be secured by a clip when fully installed, but if yours does not seem to seat, check the helmet and visor for any “zits” or “boogers” that could be blocking things from seating.  If it still does not seat properly, then a drop of superglue may be required to install the visor.  The stripe installs by first setting the hooked side of the stripe in the center of the helmet and then rocking the front part into place.  It can help to push the helmet with the stripe against a hard surface to get it to fully seat.

There is now an Astronaut Tools Kit available, with some tools, which you can find here.

Big thanks to Soozafone (aka Lucky 13 Toys) for sharing the awesome Dummy13 model, which this is remixed from! If this remix is not for you, the Dummy 13 model, and it's other remixes are definitely worth a look (and a like).

If you want to add a cool “Photon Cannon” for your Astronaut, check out ntdesign's DUMMY 13 Lamp (250% scale).

Mici has made a Moon Rover for Dummy 13, which I'm currently building to give my astronauts a cool ride across the lunar surface.  You can check it out at the link below:

https://makerworld.com/en/models/770027#profileId-705787

The Dummy 13 Alien can be found here:
https://makerworld.com/en/models/782607-alien-dummy-13-and-80-scaled-frame-armor-parts

Printing and other stuff:

The parts here are designed for regular single color printers. I've included BambuStudio 3mf files based on a Bambu X1C profile (though it should work with P1S and P1P also). There are no supports needed, since they are integrated into the frame design.  The slicer will warn about “floating regions” and suggest turning on supports, however I recommend printing without supports (they are not needed).  The frame parts will be required from the Dummy 13 v1.0 files which you can find here:
 

https://makerworld.com/en/models/638587-dummy-13-version-1-0#profileId-564186

Thanks to a tip by MK4_Expert, I re-printed my frame parts in PETG after the PLA frame joints became loose, and the PETG seems to be much better at keeping it's position - so I'd recommend printing the frame parts in PETG if possible.

Some superglue will be needed to glue the visor to the helmet, and a dab may also help on the helmet stipe insert and backpack (if you want that to be permanent).

Other Stuff:

If you like this design and want to check out some of my other Dummy 13 stuff, here are some of my Dummy 13 Weapons and Adventure Packs (and related models):

Dummy 13 Dino Safari Kit Card	Dummy 13 Weapons Pack Version 2.1	Dummy 13 Alpine Adventure Pack Version 1.0
Alien Dummy 13 and 80% scaled frame & armor parts	Dummy 13 Astronaut Tools Pack V1.3	Dummy13 Goes to the Moon Astronaut kit card (single color version)
BBQ Tools For Dummy 13	Dummy13 Goes to the Moon Astronaut kit card (AMS version)	Dummy 13 Roadside Assistance Kit

These and a few more can be found here:

Weapons Pack V2.1 - MP5SD, MP5K's, Handguns, Holsters and Katanas

Alpine Adventure Pack v1.0 - Skis, Ice Axe and Backpack for Winter Adventure Sports

Astronaut Tools Kit v1.1 - Space drill, pick, geologic collection scooper, camera and other Astronaut stuff

Astronaut Armor - Includes a helmet, backpack and other armor parts to turn Dummy 13 into an astronaut (in multicolor too)  

BBQ Tools Kit - You read that right, even Dummy 13 likes to grill up some burgers now and then

Dino Safari Pack - Everything a Dino Safari Park Ranger needs, including a cool hat!

Roadside Assistance Kit - Traffic cones, a bottle jack and other tools

Big thanks to Lucky 13 Toys (Soozafone) for sharing the awesome Dummy 13 (v1.0) model with the world. The Dummy 13 model (which this was designed for) is shared under the following license:

Note - if you see these for sale on Amazon , Etsy or anywhere else, they are not being sold with my permission. There are no "authorized" sellers of these models. They were made for the 3D printing community, not for Amazon or Etsy sellers to profit from.

If you find these models useful, please post a like or a comment with some pics of your prints. You can find the other things I'm working on at my blog here. You can also follow me here, on BlueSky or on Printables, to get news on any new stuff I post.

If you would like to support my work, you can “Boost Me", or  even Buy Me A Coffee using this link:

https://www.buymeacoffee.com/mystoopidstuffmystoopidstuff

Thanks for looking!

Cover photo Credits:
National Aeronautics and Space Administration
https://history.nasa.gov/alsj/a17/images17.html#MagA
https://history.nasa.gov/alsj/a17/AS17-147-22470HR.jpg

Also thanks to the following makers, whose models I used in making the cover image for this thing:

INVASION! The electric tea light UFO
by DrKronos

Cow 
by Orto

AT-ST Walker Kit Card
by Nakozen
 

Changelog:

12/21/2024:  Updated the model and 3MF with a carded option.  The card has all the armor parts on a card. The 3MF has as multicolor and single color option. 

5/20/2025:  Update the model and 3MF to version 1.2 R49.  This version includes a new helmet design with a snap in place stripe and visor.  The torso has also been updated.