Super Mario Dice Tower - Free 3D Print Model

Search models, users, collections, and posts

Rianski Schipanski

Toys & Games>Board Games

IP Report

Print Profile(4)

All

X1E

A1 mini

X1 Carbon

H2D

H2S

H2C

P1S

P2S

P1P

H2D Pro

X2D

A2L

0.2mm layer, 2 walls, 10% infill

Designer

4.9 h

3 plates

4.9(41)

Alternative cube base

Designer

1.5 h

1 plate

5.0(3)

Cube Ramp/Bed Scraper individual

Designer

35 min

1 plate

150% Size And More rolling, 2 walls, 15% infill

18.8 h

4 plates

Open in Bambu Studio

Boost

485

1547

569

344

Released

Description

Boost Me (for free)

If you like the model, I would appreciate a boost. It would support me to keep the models updated and to keep uploading new models in the future <3

buymeacoffee.com/derian90

Super Mario dice tower for a cozy game night. :)

For the vertical pipe and the cubes, I recommend using supports at the critical spots; otherwise, the print quality in those areas might not be optimal. If you’re using my print profile, you just need to set the support option to ‘Normal (manual)’.

Update 05.01.24: New design/layout for the cube – it now looks more like brick blocks!

0.2mm layer height

2 walls/perimeters

10% infill

Feel free to leave a comment or review if you like the model or have any suggestions for improvement. I’m constantly working on improving my models. :)

Boost Me (for free)

If you like the model, I would appreciate a boost. It would support me to keep the models updated and to keep uploading new models in the future <3

Feel free to leave a comment or review if you like the model or have any suggestions for improvement. I’m constantly working on improving my models. :)

You can also support me with a coffee :)

Comment & Rating (50)

@BrianW79

Boosted

Print Profile

0.2mm layer, 2 walls, 10% infill

great print. The supports stayed on the mat when the rest of the item was pulled off. So easy. My son loves it.

The profile uploader has replied

@derian90

I am happy to here that and thank you very much for the boost. Appreciate it :)

@the_dude_

Print Profile

0.2mm layer, 2 walls, 10% infill

great model, but could use a higher back stop along the edge. dice keep rolling off the end.

The profile uploader has replied

@derian90

Hey thanks for your comment. If you want you can check out one of the other profiles for this model there is also a single bottom part with a higher back in rounded shape which should prevent the dices to fall off the end. Best regards

(Edited)

@jmushroom

Print Profile

0.2mm layer, 2 walls, 10% infill

I printed this dice tower for my Mario review activity for elementary students. It looks great and students loved it! As others have noted, it doesn’t tumble the die very well and about 20% of the time the die doesn’t fully come out the bottom. The pipe could be a little larger with some steps inside to help randomize dice better. The print tolerance, especially with the brick block, are too tight. I had to sand down the inside to get it to fit around the pipe.

@ShopTeacher

Print Profile

0.2mm layer, 2 walls, 10% infill

Printed well and kids like it. Tolerances were too tight and should be increased a bit to make it easier to assemble. The bottom brick piece is also way too thin at the back brick joint and nearly broke just removing it from the plate so be careful with that piece.

@olref

Print Profile

0.2mm layer, 2 walls, 10% infill

No problem

Show original

@arweatherly

Print Profile

0.2mm layer, 2 walls, 10% infill

Great and easy print!!! works as expected. This was a fun print to paint with my son. There is one small issue, the connection ring between the blue pipe and the pipe lip is a little thin. It broke when I dry fitted the pieces together. Nothing a little superglue couldn't fix.

@Matt_XT600

Print Profile

Alternative cube base

I like this base plate

Show original

@Matt_XT600

Print Profile

0.2mm layer, 2 walls, 10% infill

Sehr schön.

@Carlossander

Boosted

Print Profile

0.2mm layer, 2 walls, 10% infill

excellent

@josemateuss

Boosted

Sensational, thanks for the model, I just made a small mistake in assembly, I suggest adding a simple assembly description I know, many people didn't mess up the assembly lol, but there's always a first time I really appreciate it

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Smash! The Auto-Reload Dice Tower

Rossero

24 k

11.5 k

Yoshi from Super Mario

It's a me

15.3 k

5.5 k

Dice Tower Castle Stairs

squinn

17.4 k

4.9 k

GIF

Mechanical Dice

StatusSymbol

54.9 k

17.9 k