Bambu Lab Spool Stealth Snap In Filament Clip PLA+ - Free 3D Print Model

Search models, users, collections, and posts

BATTCAVE

3D Printer>3D Printer Accessories

IP Report

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

4 PACK - PLA+ - 0.08mm layer, 2 walls, 15% infill

Designer

20 min

1 plate

4.6(52)

Brim added - 0.08mm layer, 2 walls, 15% infill

32 min

1 plate

4.9(31)

Open in Bambu Studio

Boost

180

515

586

429

Released

Description

Bambu Lab Spool Stealth Snap In Filament Clip PLA+

For best results use PLA+/Pro – Standard PLA will give mixed results.

Ultra low profile clip that presses in firmly from the inside of the spool to be a permanent filament clip for the life of the spool. Will work on any Bambu Spool with the 3.6mm Holes and no more than 3.6mm thick. Micro-fins lock it in.

Attach ONCE and be done with it for the life of the roll. It will not interfere with printing or storing on a rack. Be sure to align the hole before pushing it through otherwise you can rotate it with small tool.

These are TINY so filament matters. They fit perfectly tight with Sunlu PLA+. If you have trouble with size, try another filament. Considering how much filament they take, experimenting is cheap. :P

100% AMS Compatible - Align spool so the clip clears the funnel when rotating on the RIGHT side of the spool. (Double check your AMS, an odd revision could be out there that wants it on the left but everything I have seen shows the right side being the correct side)

Example printed in Sunlu Gray PLA+

Comment & Rating (94)

@LizardTail

Print Profile

4 PACK - PLA+ - 0.08mm layer, 2 walls, 15% infill

Works great!

@lubomir.blaha

Print Profile

Brim added - 0.08mm layer, 2 walls, 15% infill

Works great (the missing one is already used)

@jon6V27E

Print Profile

Brim added - 0.08mm layer, 2 walls, 15% infill

Printed in ABS, excellent quality. Thank you for sharing

Show original

@Jobbo

Print Profile

4 PACK - PLA+ - 0.08mm layer, 2 walls, 15% infill

fast, clean and super useful. thank you so much!

@Pinguiii

Print Profile

4 PACK - PLA+ - 0.08mm layer, 2 walls, 15% infill

The clips fit perfectly print quickly and use little filament I immediately printed several to keep as spares :) Thank you very much

Show original

@bdwilson

Print Profile

4 PACK - PLA+ - 0.08mm layer, 2 walls, 15% infill

appeared to print well but sheered off after insertion. I’ll try again with a non-silk filament. it was just what I was trying to get rid of.

@LemonSheep

Print Profile

4 PACK - PLA+ - 0.08mm layer, 2 walls, 15% infill

works good

@user_3488339990

Print Profile

4 PACK - PLA+ - 0.08mm layer, 2 walls, 15% infill

Thank you for this ingenious minimalist design I already use a similar design for cardboard spools This is attached from the outside to the inside Yours is even more minimalist and the “threaded fastener” its name “Stealth Snap in” is simply ingenious Since the filament is never cut at the same point on the spool circumference it is only logical to simply attach another clip Also because the “thread” suffers when removed and when reinserted in another hole it no longer holds as well But honestly at the next filament cut the clip will be needed again elsewhere In my case so far no more than two of the clips have been required in any spool They always remain inside On which side of the spool it is in my case with AMS Lite is irrelevant

Show original

@Vittorino

Print Profile

Brim added - 0.08mm layer, 2 walls, 15% infill

Easy and quick, very convenient for Bambu Lab plastic spools Not suitable for all spool brands

Show original

@user_962201574

Print Profile

Brim added - 0.08mm layer, 2 walls, 15% infill

works perfectly

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.