Search models, users, collections, and posts

Tent Zipper Air Duct v2 3 inch/76mm

ScottGMcCarty
Hobby & DIY>Sport & Outdoors
IP Report

Print Profile(1)

All
X1 Carbon
H2D Pro
H2D
A1
H2S
P1P
P2S
X1E
H2C
X1
P1S
X2D
A2L
0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
3.8 h
1 plate
4.6(10)
Open in Bambu Studio
Boost
97
222
19
6
439
136
Released 

Description

Membership

Want to sell this item. Start a commercial membership.

Join

This is used to attach a 3 inch/76mm flex duct to a tent zipper window or door. It fills the gap around the duct. Make sure to print using a material that can handle the heat you intend to put through it. This is version two with a 75mm hole to make use of the vent that comes with the heaters.

tent vent
zipper vent
zipper duct
tent duct
diesel heater
chinese diesel heater
camping
tent
rooftop tent
air conditioner
3 inch duct
duct
76mm
75mm

Comment & Rating (19)

(0/1000)
@BuildNCode1
Print Profile
0.2mm layer, 2 walls, 15% infill
This was a great profile! The supports were kind of hard to remove, but I eventually got it. My duct hosing fit perfectly, as you can see in the picture. Thank you for posting!
0
Reply
@Stompies_02
Print Profile
0.2mm layer, 2 walls, 15% infill
Prints nice, supports are hard to get out, but not much you can do. Haven't tired it yet though
The profile uploader has replied
0
Reply
@scottgmccarty
If you print in PETG and use PLA as interface layer they come out really easy.
0
Reply
@facelord
Replying to @scottgmccarty :
Does PETG withstand the temperature of the hot air from the diesel heater without melting?
0
Reply
@user_50187804
Would you be able to design one for a double set of ducting?
1
Reply
@1.BAD.DAD
My P1S did not love printing this in ABS. wanted to warp and it was nice and warm. maybe my fans were on by accident. I was able to heat and reshape it no problem. also had to file the inlet a MM or two to get the duct in! but i do love it. no shade, its most likely my user error on the print issue.
(Edited)
0
Reply
@PrintNPlayNZ
Print Profile
0.2mm layer, 2 walls, 15% infill
First print I tried using PLA on the top surface of the support that did not go well so I printed again fully just in PETG and this one came out much better just like everyone else supports a super annoying to remove but can’t do much about it apart from that great print
0
Reply
@ian.santiago
is there a 3 inch/89mm version of this model? trying to fit a portable AC duct to a tent zipper.
0
Reply
@user_3446759502
https://makerworld.com/models/745139
0
Reply
@Stompies_02
Looks good!
0
Reply
@PipeCRO
Boosted
Just what I need !! TX !!
0
Reply
@PipeCRO
Boosted
Print Profile
0.2mm layer, 2 walls, 15% infill
Just What I need !!!
0
Reply

License

If you want to use this model commercially, please join my membership.
Join Now
This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Air Pressure Tank V2
GIF
Air Pressure Tank V2
Patopato_Design
31.6 k
10.9 k
Zipper Bookmark
Zipper Bookmark
Modelicious Creations
28 k
10 k
Tent Zipper Air Duct 3 inch/ 76mm
Tent Zipper Air Duct 3 inch/ 76mm
ScottGMcCarty
419
101
Sunlu AMS lite adapter
Sunlu AMS lite adapter
BRADCAD
39 k
6.1 k