Rugged Storage Box V1 (Parametric, Screwless)

Copyright Claim

Rugged Storage Box V1 (Parametric, Screwless)

Boost
380
711
104

Print Profile(19)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

Box 160x120x60
Box 160x120x60
Designer
6.9 h
2 plates
4.9(19)

Box 100x50x40
Box 100x50x40
Designer
2.8 h
1 plate
4.9(11)

Box 160x80x40
Box 160x80x40
Designer
4.2 h
1 plate
4.8(6)

Box 100x50x60
Box 100x50x60
Designer
3.5 h
1 plate
4.8(6)
Click to see more

Boost
380
711
104
41
897
313
Released

Description

The Allround Box V1.5 OUT NOW! 

https://makerworld.com/en/models/492885#profileId-406546

This is the older Version of “The Allround Box”!

Please switch to the new one, if you don't need replacements parts from this site.

 

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

The box is assembeld with pieces of filament, so screws arn't needed anymore!

 

If the filament falls out of the hinges, glue the ends a little with super glue.

 

For the sealing, TPU can be used.

 

Attention:

Pay attention to the comments in the parametric design in Fusion 360!

 

Release Notes:

27.03.2024

  • The V1 avaliable now!
    • Screws are replaced trough small pieces of Filament that perfectly fit in!
    • The Design in Fusion 360 is Parametric, most of the dimension can be changed.
    • The Latch design stands out with it's wheels, which lock into place perfectly!

31.03.2024

  • Update V1.2!
    • Some model issues fixed.
    • Better fit for non sealed boxes.
    • Filament holes widened

05.04.2024

  • Update V1.3
    • Some parametric design issues fixed.
    • TPU seal geometry more water resistant

12.06.2024

 

Comment & Rating (104)

Please fill in your opinion
(0/5000)

An entire day of printing, $25 worth of plastic and after assembling everything (had to actually sand the filament slightly smaller to get it to fit) the latches were too wide. I thought I would trim a little off the rib and the case split. Waste of time and money.
The designer has replied
8
Reply
Hi, thanks for your comment! I‘m sorry for your problems, but on which printer did you print it?
1
Reply
what did you print, on what printer? $25 is a lot of PLA
2
Reply
Replying to @RDesigns :
P1S. I'm thinking that the parametric side of things is restricted to only a cple of options
1
Reply
Thanks, made a storage box for my Apple AirTags. Noticed your license does not permit remixes to be posted. Would you like to amend that so I can post a remix? Entirely up to you!
The designer has replied
3
Reply
Hi, thanks for pointing this out to me. License should be updated and now allow remixes to be posted!
1
Reply
Great parametric model, needed some tweaking after customization in Fusion in my case. First the latches came out way too wide (about 3mm in total), had to scale them down to fit on X. I recommend printing the shells first, then measuring the latches to fit if you're not adept enough to do the changes in Fusion, like me (just cut off the ends symmetrically, which can be easily done in Bambu Slicer). Using filament for the hinge works fine, on the latches it's a tight fit, had to carefully force it in with pliers. The latches themselves do work fine now, they could have a bit tighter fit however, will probably experiment with slightly increased wheel diameter to remedy that.
The designer has replied
0
Reply
Hi thanks for your comment and your describtion, the latch size adjustment unfortunatly don't works at the moment correctly, but soon there will be a new version of "The Allround Box" which will fixes all of it's issues. At the moment I'm working on the renderings for it's release. If you would like to try out the new V1.5 of the f3d file, I will try to send it over!
1
Reply
Replying to @RDesigns :
Sure would love to give it a go, got another box lined up for print in a few days.
0
Reply
Boosted
Print Profile
Box 100x50x60
Fantastic model! Thanks for sharing! Everything fits great. I have printed it all with CCtree st-pla. Used the packing material from the printer as internal foam protection.
2
Reply
Print Profile
Box 100x50x40
I printed the 100x50x40 model, and it couldn’t have turned out any better! Parts assembly was smooth, and everything went together nicely. The screwless design is fantastic; the 1.75mm filament holds it all together very well. (Cut your filament carefully and soften the ends. Then mushroom them with your fingertip. They’re now locked in! See my close up photo of the latches for a visual.) The TPU gasket is a nice touch! Looking forward to making more. Thank you Redesigns!
2
Reply
Great box easy to assemble! And moreover parametric!!! Thanks!
1
Reply
Print Profile
Box 160x120x60
Simple to print, simple to build!!!
1
Reply
Awesome! Just what I was looking for! Needed a box for my wireless guitar system and used the Fusion file to modify it to my needs. Came out great! Thx!!! The foam inside came with the original package (155x101x42mm inside).
1
Reply
Print Profile
Box 160x80x40
printed nicely, I really like it but unfortunately I could not fit filament in pin holes as they were very tight, I used buss wired instead and it worked out! I need to get the seals done still but thanks!
1
Reply
Print Profile
Box 160x120x60
great box just finishing up the lid now
1
Reply