A1 Mini Wyze v3 Mount by ondrovic

ondrovic

3D Printer>3D Printer Accessories

Print Profile(1)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

A1 Mini Only - 0.2mm layer, 4 walls, 15% infill

Designer

5.2 h

5 plates

4.7(6)

Open in Bambu Studio

Boost

Released

Description

There some great ones out there but I didn't like the angle so I design this one to use to allow you to reposition the camera.

Note:

I have had a few of you ask if this fits the A1, currently I don't have an A1 to test with, I believe there are slight differences between the two.

Update: Thanks to @trevstein96 from testing on the A1 its confirmed not to work, I will attempt to make one compatible but again since I don't have one I will not be able to test.

Features:

Uses original wyze base with motion system
Two part printing means limited supports
Privacy, you can angle your camera so your not in view
Alternate adapters

Version History:

2024-01-01 - Initial Release
2024-01-05 - Updated designs to include an additional two mounts
2024-05-03 - Re-uploaded project, some users reported the dove tail was too small on the mount, this fixes that issue

Comment & Rating (24)

@mikklovin

Fit is great on the A1 mini, but I’m not sure what happened as the slot for the attachments is very shallow. Attachments slips on, but isn’t held in very well. Not sure if something changed after I used the .4 nozzle through Bambu Handy, but it’s not right at the moment.

The designer has replied

@ondrovic

Not sure what happened with that, def looks like the dove tail is to shallow on the mount. Looking into it now

@ondrovic

Replying to @ondrovic :

Looks like something happened to the mount, I am going to reupload the project

@ondrovic

@mikklovin I have re uploaded the project, you'll notice now that the a1 mini mount has a larger dove tail, not sure what happened with the other one this one should fix the size issues. Thanks for reporting it.

@makkerdam

Print Profile

A1 Mini Only - 0.2mm layer, 4 walls, 15% infill

Fits my A1 mini - Awiating my Wyze camera

The designer has replied

@ondrovic

Awesome thanks for the review, now if we could just get it work natively from within the handy app.....

@mikebdub

Will this work on the A1 as well? The hotend setup's look the same but I wanted to make sure before I ordered the v3 cam. I like the ability of being able to change the angle. How's it hold up to the fast movements?

The designer has replied

@ondrovic

I don't know if it will work with the A1 I believe they are different, but since I don't have on yet, I cannot test it. You could always print out the holder piece and test fit it to see before ordering the cam. At only an hour to print plus .86 cents is way cheaper than buying the cam first. If you do print it let me know

@trevstein96

Replying to @ondrovic :

it doesnt fit i just tried i wish it did dont care for the other A1 mounts

@ondrovic

I wa 99% sure it wouldn’t work, silly the inconsistency sometimes. I’ll see if u can find the measurements anywhere and see if I can get one that will work.

@3Dchris

Is there one like this that uses the default .4 nozzle and PLA? I don’t have either but I’ll get them if not.

The designer has replied

@ondrovic

You should just be able to change your settings and material in the slicer to match what you have

@3Dchris

Replying to @ondrovic :

I’ll give it a shot thanks

@ondrovic

Replying to @3Dchris :

No problem, I think the only reason I used PETG was for the flex but now that I think about it PLA should be just fine

@Renard.pecheur1

Print Profile

A1 Mini Only - 0.2mm layer, 4 walls, 15% infill

Other Issues:la partie on on emboite les deux morceaux n’etais pas de la même taille. j’ai coller et ajustet avec un crayon 3d

The designer has replied

@ondrovic

Which two parts were not the same, as there are a couple of different options to print out, would you mind sending me a photo of what you printed out? As I printed all the variations myself to make sure they fit properly

(Edited)

@Renard.pecheur1

here is a picture

@ondrovic

Replying to @Renard.pecheur1 :

So that part isn't supposed to be super tight it is supposed to allow for the bracket to slide in and out, I will double check the files and make sure I didn't upload the wrong one by mistake. Can you tell me which bracket you printed out, off of which plate?