Filament Spool Holder
Copyright Claim
Filament Spool Holder
Boost
226
372
35
Print Profile(1)
0.2mm layer, 2 walls, 15% infill
Designer
8.6 h
2 plates
Boost
226
372
35
2
747
219
Released
Description
Fit in 18 filoment spools.
All fits well.
Without glue.
Tube diameter 4 cm or 1,5748 inches.
Tube length 71 cm or 27,9528 inches.
Comment & Rating (35)
All
Print Profile
0.2mm layer, 2 walls, 15% infill
4 hours and 255g of filament down the drain. the stand don’t fit in the legs. used profile with out changes.. ugh
this is on both sides.
(Edited)
The designer has replied
0
Reply
Please try to pull it harder. I had this problem too. I just started whit my leg on and it fits perfectly.
0
Reply
Replying to @Bananana
What do you mean by “pull it harder”.
Also the hole for pvc won’t fit 1.5”, 1.25”, or 1”. Took the piece to Lowe’s to get fit and it didn’t
0
Reply
Replying to @Bananana
I can use a heat gun to get it to fit barely. But holes are still jacked up. 1” is too small for hole and 1.25” is too big
0
Reply
***** let me save all the u.s. people the trouble and money... lol. I went and grabbed 1 1/2 inch pvc not thinking of outer diameter.. cut it, and it didn't fit. Went back and measured o.d. of 1 1/4 pvc with was under 1.5", came home, cut it... still didn't fit!! so the correct pic pipe is 1" works perfectly. 3d printed pieces fit together beautifully! I love it, does exactly what I needed!!! *****
9
Reply
1" is to small. I just for back from Home Depot and 1" just flops around.
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Will not fit 1.25” schedule 40 PVC. I used 1” and it works great.
0
Reply
what desk is that? your setup looks amazing!
0
Reply
it is from Harbor Freight. 99.00. Very surprised it has almost zero movement and is very stable
0
Reply
Boosted
Print Profile
0.2mm layer, 2 walls, 15% infill
I used 1.5 inch wooden dowels to add stability for the 3 foot shelf. works great, great print thanks...
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Found some aluminum rods, cut them to 90cm. Fits perfectly. Thanks for the design. Love it
0
Reply
Where did you get the tubes?
The designer has replied
1
Reply
Looks like PVC pipe from Home Depot.
1
Reply
It's a PVC tube and the size is DN 40 (not sure if it is a EU or global standard). Price should be around 2 EUR per meter.
0
Reply
Replying to @fawcettm
you’re right
0
Reply
Cannot get the pieces together. Two of the pieces broke while trying to get them to fit together. Good concept though.
(Edited)The designer has replied
0
Reply
you needed print with petg or abs not pla it will break. And please do not change size of parts
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
print very well
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
I like it just wish that there was a link to were to buy the sticks
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Love this and currently using this for all my filaments.
0
Reply
© 2024 MakerWorld