X1C Screen Bezel by mrlebl0nd71

mrlebl0nd71

3D Printer>3D Printer Accessories

Print Profile(3)

All

X1 Carbon

P1S

P1P

X1E

REV_3 0.16mm layer, 3 walls, 15% infill

Designer

7.9 h

3 plates

4.5(11)

REV_3 0.2mm layer, 3 walls, 25% infill

Designer

7.7 h

3 plates

4.3(3)

TPU 0.2mm layer, 3 walls, 15% infill

Designer

6.4 h

1 plate

Boost

217

269

143

Released

Description

J'ai créé un cadre pour mon écran X1C.

Le fait qu'il soit possible de le bouger me déplaisait. Il est maintenant fixé.

Il est volontairement moins long sur la partie supérieure pour permettre le passage de mon riser. Le modèle a été réalisé en collant une bande double face 3M sur la partie prévue à cet effet.

Si le modèle demande des modifications, merci de me les communiquer.

Je ne suis pas professionnel et je réalise cette pièce par plaisir.

Trois versions sont disponibles :

Simple sans écriture
Un modèle avec un creux pour éventuellement ranger des outils
Un modèle avec l'inscription "Bambulab" extrudée de 0,01 mm

Plateau 1: inscription Bambulab

Plateau 2: classique

Plateau 3: avec porte outils

Remarque : Le débit doit impérativement être calibré.

Merci d'avoir téléchargé mon modèle.

/!\ le PLa matte n'est pas la meilleur option /!\

I created a frame for my X1C screen.

The fact that it could be moved displeased me. It is now fixed.

It is intentionally shorter on the upper part to allow my riser to pass over. The model was made by attaching a 3M double-sided tape to the designated part for this purpose. If the model requires modifications, please let me know.

I am not a professional, and I am making this piece for pleasure.

Three versions are available:

Simple without any writing
A model with a hollow space, potentially for storing tools
A model with the "bambulab" inscription extruded by 0.01 mm

Plate 1: Bambulab inscription

Plate 2: classic

Plate 3: with tool holder

Note: The flow rate must be calibrated without fail.

/!\ Matte PLA is not the best option. /!\

Thank you for downloading my model.

Comment & Rating (42)

@Niellex

Print Profile

REV_3 0.16mm layer, 3 walls, 15% infill

Nice print with PLA-CF. The angle of the screen it off on mine for some reason. screen doesn’t sit flush and it’s as far up as it can go. Double sticky tape holds it on great.

The designer has replied

@e.ferazzini

I printed the version without any branding, but I have the same problem. I printed it facing down, so I'm sure the front face is flat. I think the problem is relate with some angle inside the frame. even if I push and apply a bit of force it won't get correctly in place

(Edited)

@mrlebl0nd71

Replying to @e.ferazzini :

je regarde cela au plus vite

(Edited)

@OldSalty3D

I love this! Looks like it's factory installed! Nice model!

The designer has replied

@mrlebl0nd71

thanks 👍

@hadessuk

Print Profile

REV_2 0.2mm layer, 3 walls, 15% infill

Printed the version with the toolholder in PLA. A little bit hard to insert, but fits snuggly.

The designer has replied

@mrlebl0nd71

Since there are several of you who have the problem. I will enlarge slightly 👍 thanks for the feedback

@Unforgivenll

REV_2 0.2mm layer, 3 walls, 15% infill 2024-01-10 ⭐⭐⭐⭐⭐ Excellent model. Thank you.

(Edited)

@danghaihuynh89

Print Profile

REV_2 0.2mm layer, 3 walls, 15% infill

This was a sturdy piece and looks great. for me, it was extremely difficult to install and remove. The fit on the screen was tight. I had to cut my screen out of it with heavy cutters. This may have been due to my inexperience. Author was responsive with troubleshooting.

(Edited)

The designer has replied

@mrlebl0nd71

have you properly Calibrated and dry your filament before ? what use filament ? Better résultats pla cf👍

@danghaihuynh89

That’s a good point. I used PLA basic. Thanks for the tips.

(Edited)

@mrlebl0nd71

Replying to @danghaihuynh89 :

try pla-cf dry otherwise upscale the model by a few small percentage. not much. then come back to me to tell me more 😉 and change your rating. thought dehydrated the filament.

@Alpineskyline

Print Profile

REV_3 0.16mm layer, 3 walls, 15% infill

Nice work, thank you for the time you spent on this. I ended up flipping screen side face down and adding some color to that surface. turned out great!

The designer has replied

@mrlebl0nd71

great👍 thank you for your feedback I'm glad you like this piece. very good idea for the screen color 👍

@mrlebl0nd71

hello @Alpineskyline . New download with screen protector

@Stephanaccessor

Print Profile

REV_3 0.16mm layer, 3 walls, 15% infill

Well done, If you print in the right position you have perfect smooth surface and it fits good (double side Scotch needed)

The designer has replied

@mrlebl0nd71

merci pour votre commentaire j'espère que cela vous plaira 😁

@the.v0ha

Would be nice if there was a version with full screen cover.

The designer has replied

@mrlebl0nd71

je vais y réfléchir.👍

@drdrfoerster

Would this work printed in TPU? I like the idea of a little more shock absorption with a more flexible material. I am a novice, so I have no idea if this is as simple as changing the filament type or if other modifications would have to be made.

The designer has replied

@mrlebl0nd71

try it :D

@StayLevel

Print Profile

REV_3 0.16mm layer, 3 walls, 15% infill

The designer has replied

@mrlebl0nd71

merci pour les 5 etoiles