Lead Screw Shield with magnet Remixed by FrancescoM

Remixed by

FrancescoM

3D Printer>3D Printer Accessories

Print Profile(7)

All

P1P

P1S

X1 Carbon

X1E

DX 10x3mm 0.2mm layer, 2 walls, 15% infill

Designer

2.9 h

1 plate

4.9(7)

SX 10X3mm 0.2mm layer, 2 walls, 15% infill

Designer

2.9 h

1 plate

5.0(3)

DX 8x3mm 0.2mm layer, 2 walls, 15% infill

Designer

2.9 h

1 plate

4.7(3)

SX 8x3mm 0.2mm layer, 2 walls, 15% infill

Designer

2.9 h

1 plate

5.0(1)

Click to see more

Open in Bambu Studio

Boost

328

120

Released

Description

07/01/2024 new version 4.0

https://makerworld.com/en/models/128344#profileId-138948

19/11/23 Added version for 10x3 mm with more tolerance if too wide use glue to block them

Added version for 8x3mm magnets

+++++ NO support ++++

New version 2.1

This remix has 10x3mm magnets which make it more stable and easy to remove to lubricate the bars

the magnets are easily available at this link

https://www.amazon.it/neodimio-millimetri-diametro-confezione-Magnetpro/dp/B07JGR8CQ2?ref_=ast_sto_dp

Comment & Rating (39)

@craigandrews

Printed the 8x3mm version. The magnet spots were a bit tight, requiring me to do some filing before the magnets would fit. It looks nice and appears to do its job well. Seems like a good idea and I'm glad to have it.

The designer has replied

@FrancescoM

thanks for your advice. I was in the office and not at home and I wanted to make it happen quickly. Now I'll change the hole. If you liked it you could reward me with some stars, regards Francesco

@Tethgar

The print profile is no longer public

Support was impossible to remove, had to add negative part and use my own supports. good model otherwise thank you for uploading

The designer has replied

@FrancescoM

there are no supports in my project you have to print it vertically. try again

@Tethgar

@FrancescoM I don't know why this posted to this model, I rated the original model from Bambu Studio. Sorry about that.

@NaNraY

Print Profile

DX 8x3mm 0.2mm layer, 2 walls, 15% infill

Works well but doesn't cover the bottom as well so not the prettiest when open

The designer has replied

@FrancescoM

Thank you for great rating, better not to get too close to mechanical parts to avoid damaging them.

@mikesn31

Print Profile

DX 8x3mm 0.2mm layer, 2 walls, 15% infill

love it thank you!

The designer has replied

@FrancescoM

Thank you for great rating!

@Whoooo

The print profile is no longer public

The print quality is good but design is not optimal as the magnet (Ø10mm) has to be pressfit which may break the part(should add more tolerance). Also its functionally flawed; the cover may hit the print bed and stop it from going all the way up and the bed can push it up so it hits the print head resulting in the printer stopping.

The designer has replied

@FrancescoM

Upon kindly request, I created a variant for an 8mm guy and he told me to add a greater tolerance, said done. You're the first to complain about my work and instead of giving good advice you gave me 2 stars. I wasn't at home and couldn't answer you sooner. on makerword we are not all professionals but we are passionate about 3D printing. If you don't understand the spirit of this community I don't know what to tell you I recommend you frequent paid sites where there are professionals.

(Edited)