A1 mini竹屎导引器
Copyright Claim
A1 mini竹屎导引器
Boost
97
178
39
Print Profile(2)
0.2mm layer, 3 walls, 15% infill
Designer
37 min
1 plate
0.16mm layer, 2 walls, 15% infill
46 min
1 plate
Open in Bambu Studio
Boost
97
178
39
6
711
156
Released
Description
v2版本已发布，在安装后存在的缝隙处增加了一个挡板，并且增加了整体的高度，可以确保竹屎通过导引器垂直落入下方的收集盒中。
A1 mini / A1竹屎引导器V2 来自 kurikoo - MakerWorld
可以引导竹屎垂直落下，防止乱飞，在下方放置一个盒子即可收集竹屎。整体很轻巧，使用PETG打印重7.8g。
组装方法：打印完成使用胶水将两部分固定在一起，等胶水固化后卡在吐料组件一端即可。
Comment & Rating (39)
All
A1可以用吗
The designer has replied
0
Reply
应该是可以的，a1mini和a1的吐料组件好像是一样的
1
Reply
Replying to @kurikoo
A1使用这个不太合适，请问能帮忙修改一下吗，那个间隙每次都会挂竹屎
0
Reply
Replying to @kurikoo
A1使用这个不太合适，请问能帮忙修改一下吗，那个间隙每次都会挂竹屎
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
Nice
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
Came out perfect, thanx for the great design.
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
Passt sehr gut!
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
Ich bin gespannt, wenn es zusammengeklebt ist, wie es ist. Ansonsten denke ich ein super Tool.
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
0
Reply
petg打会好一点吗？我用pla打的Z轴强度不行一碰就断了
The designer has replied
1
Reply
层间粘合不足的话可以提高温度试试，petg、pla应该都没问题
0
Reply
Nice design. I printed in PLA (Esun PLA Lite) and it worked fine. It's a shame the parts need to be glued together, I'm sure a slide-together design could be possible, but it's a small downside on an otherwise excellent part. Printed in grey it fits in beautifully with the grey components on the A1 Mini.
0
Reply
不涂胶水petg失败了三次，pla一次就成功了
The designer has replied
1
Reply
我是在导引器内圈加了裙边，用petg打印就没问题了，我的习惯是从来都不涂胶
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
printed in petg worked out perfect.
(Edited)The designer has replied
1
Reply
感谢反馈，我也是使用petg打印的
0
Reply
瞎了，打完才发现有个V2
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share AlikeRemixes (1)
Related Models
© 2024 MakerWorld