TPU Dust Cover for P1P, P1S, and X1 Z Axis

TPU Dust Cover for P1P, P1S, and X1 Z Axis

Boost
147
379
27

Print Profile(2)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

TPU, 0.2mm layer, 2 walls, 15% infill
TPU, 0.2mm layer, 2 walls, 15% infill
Designer
14 min
1 plate
5.0(22)

PLA-   0.2mm layer, 2 walls, 15% infill
PLA- 0.2mm layer, 2 walls, 15% infill
14 min
1 plate

Open in Bambu Studio
Boost
147
379
27
7
308
204
Released

Description

I changed the geometry of my original dust cover for P1 & X1 to better suit TPU and to make a better seal.

If you do not have TPU, please print the version linked above for PLA, PETG, ABS, or ASA.

 

This cap completely covers the top of the z-axis threaded rods to keep out dust and filament bits.

(2) covers print in roughly 14 minutes and about 1.2 grams of filament.

  • Print settings are very important, so please use the included print profile w/ a 0.4mm nozzle.
  • Make sure your TPU is dry!
  • This needs to be printed slowly - most of the speeds have been tuned to 30 mm/s.

There is a round cutout so the top of the rod/rubber plug does not rub against the printed cover!

Optimized for 0.20mm layer height.

Installation:

  1. Simply push into place with your fingers, and work around the edge in a circular pattern.
  2. The outer edge of the cap is meant to fill the space between the metal bearing and plastic.
  3. This creates a seal, and holds it in place with friction.
Cross section view

 

This should fit well because I printed around 20 to verify consistent results.

Due to variances in printing, you might want to print 4 and choose the best 2.

You can also try scaling X/Y by a very small amount in the slicer - maybe 0.2% - 0.5%.

 

Comment & Rating (27)

Please fill in your opinion
(0/5000)

Print Profile
TPU, 0.2mm layer, 2 walls, 15% infill
so cute, and so easy to print with a P1S. thank you 👍
The designer has replied
0
Reply
I think you uploaded the wrong photos, lol
(Edited)
1
Reply
Replying to @br1acc :
ho my gosh, you're right 😅😅😅
(Edited)
1
Reply
now the good ones ! so sorry 😄
(Edited)
1
Reply
Print Profile
TPU, 0.2mm layer, 2 walls, 15% infill
gedruckt mit Eryone TPU und Revo HF Obxidian Nozzle.
1
Reply
Print Profile
TPU, 0.2mm layer, 2 walls, 15% infill
A perfect fit 👍
1
Reply
Print Profile
TPU, 0.2mm layer, 2 walls, 15% infill
Perfect match !!!
1
Reply
Print Profile
TPU, 0.2mm layer, 2 walls, 15% infill
print perfect fit on nice and snug just a quick nice print in tpu
0
Reply
Print Profile
TPU, 0.2mm layer, 2 walls, 15% infill
1
Reply
Print Profile
TPU, 0.2mm layer, 2 walls, 15% infill
I printed by object to prevent stringing and they fit perfect.
0
Reply
Print Profile
TPU, 0.2mm layer, 2 walls, 15% infill
Fit as intended
0
Reply
Print Profile
TPU, 0.2mm layer, 2 walls, 15% infill
One of my first TPU prints and had 0 issues, print quality was spot on and fit perfect!
0
Reply
Print Profile
TPU, 0.2mm layer, 2 walls, 15% infill
great fit!
0
Reply