XL - Two tray /utility/ box - two cantilever trays by BHMarten

BHMarten

Tools>Organizers

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 3 walls, 35% infill

Designer

29.7 h

5 plates

5.0(21)

Boost

983

1701

1.3 k

173

Released

Description

Please consider a Boost Token reward, if you like the model, thank you.

The weight of filament needed : 950 - 1000g

You need to use M3 size nuts and bolts to assemble the box.

Information can be found in the attached image.

For the hinges and the buckles, it is possible to drip instant glue into the screw hole before screwing to fix it.

All printable parts take up 3 heating pads, I recommend to print a combination of e.g. tray and lid for printing.

dimensions : 229x140x158 mm without handle

here is a link to my smaller box : https://makerworld.com/en/models/225569#profileId-243585

here is a link to my biggest XXL box : https://makerworld.com/en/models/489511#profileId-402755

Building the box is fun, enjoy everything.

Comment & Rating (54)

@user_2666363336

不错不错打印上盖需要支撑其他不需要

@user_2450591061

请问螺丝都需要多长的

@petrkilar

Boosted

Print Profile

0.2mm layer, 3 walls, 35% infill

nice storage box design, thanks to the author

The designer has replied

@BHMarten

nice job !! thanks

@Larcen7

Boosted

This turned out great, and your instructions were easy to follow. I printed in Bambu matte grey and white. The strength of the box is very nice, and even with the bolts all tightened, the trays move freely. Very nice!

The designer has replied

@BHMarten

Thank you.

@Larcen7

Boosted

Print Profile

0.2mm layer, 3 walls, 35% infill

Luckily, I had a random M3 bolt set on hand, so I decided to try this box. And I am glad I did! This turned out great, and your instructions were easy to follow. I printed in Bambu matte grey and white. The strength of the box is very nice, and even with the bolts all tightened, the trays move freely. Very nice, and I will definitely be boosting!

The designer has replied

@BHMarten

Helo, thank you very much for your nice comment ! Nice print !

@Andy_E

Boosted

Print Profile

0.2mm layer, 3 walls, 35% infill

Genau richtig für mein LED-Material. Vielen Dank

(Edited)

The designer has replied

@BHMarten

Beautiful !!

@Cav9871

Boosted

Print Profile

0.2mm layer, 3 walls, 35% infill

great job

@mathias.haertel

Boosted

Print Profile

0.2mm layer, 3 walls, 35% infill

The designer has replied

@BHMarten

Nice job !

(Edited)

@chrisdarkki

Boosted

Hi! Love the model so far. I was wondering is there a chance of stretching this to a width of 250mm on the outer box? I would try it myself off the cuff, but I'm afraid I will screw up the proportions. Also would even wider like 30cm work, but with the base split in to two interlocking parts?

The designer has replied

@chrisdarkki

Boosted

I was thinking if I only grow the width of the boxes and trays by the same amount, but leave all the other measurements like height and depth the samel, then there should be more worries, right?

@BHMarten

Hello, I think that an extension to 250mm would be possible, the shelves, lid and bottom and the handle would be expanded.. but in the second axis it would be a problem because of the opening mechanism.

@chrisdarkki

Boosted

do you think the width will be a factor with the hinges if the depth is not touched? Because the hinges only moven in the up and down and front to back dorection. Right? I would love it I can fit longer items eg. Hammer or longer screwdrivers in there. So if I make each part longer by the same amount of millimeters (not percent) it could work just like that?