Two tray /utility/ box - two cantilever trays
Copyright Claim
Two tray /utility/ box - two cantilever trays
Boost
353
626
48
Print Profile(2)
0.2mm layer, 3 walls, 33% infill PLA
Designer
15.4 h
3 plates
0.2mm layer, 3 walls, 33% infill
14 h
5 plates
Open in Bambu Studio
Boost
353
626
48
32
627
251
Released
Description
Please consider a Boost Token reward, if you like the model, thank you.
The weight of filament needed : 450 - 500g
You need to use M3 size nuts and bolts to assemble the box.
Information can be found in the attached image.
For the hinges and the buckles, it is possible to drip instant glue into the screw hole before screwing to fix it.
All printable parts take up 3 heating pads, I recommend to print a combination of e.g. tray and lid for printing.
here is a link to my XL box /wide 230mm/ : https://makerworld.com/en/models/475478#profileId-386265
here is a link to my XXL box /wide 230mm/ and 189mm high : https://makerworld.com/en/models/489511#profileId-402755
Building the box is fun, enjoy everything.
Comment & Rating (48)
All
Fun to print, more fun to build! Looking forward to a larger box and any other variations as I will be printing them!
The designer has replied
1
Reply
Wow !!! Very nice ! Thx. XL BOX finished but rewards system was destroyed and I am waiting change.
1
Reply
Replying to @BHMarten
Whoa, looks awesome!
0
Reply
Boosted
absolute beauty! printed without a problem
The designer has replied
0
Reply
Nice ! Thx
0
Reply
Print Profile
0.2mm layer, 3 walls, 33% infill PLA
I already printed the XL version, but I couldn't resist and printed the smaller one. Super model, all parts fit well and the print profile is OK
The designer has replied
0
Reply
Nice one.. thx for post.
0
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 33% infill PLA
se ve muy chula la impresión
The designer has replied
0
Reply
Hello.. nice job.. during next week i will present XL version box with M3 nuts and bolts.
0
Reply
Print Profile
0.2mm layer, 3 walls, 33% infill PLA
very useful print some tolerances are too loose
The designer has replied
0
Reply
Hello, can you please specify which tolerances would need correction in your case? I printed 2 boxes and had no problem. I can check it.
0
Reply
Print Profile
0.2mm layer, 3 walls, 33% infill PLA
Turned out great! 👍
The designer has replied
0
Reply
nice .. beautiful print ! I think the XL version will arrive within a month :)
0
Reply
Print Profile
0.2mm layer, 3 walls, 33% infill PLA
I changed some of the supports, for example for the handle, in total good design
0
Reply
sorry, but what is the meaning with nut one sot, two dots, three dots?
The designer has replied
0
Reply
Ah, my bad I found the meaning. the cantilevers have those dot markings on which orientation they are. Going to start this project today!
0
Reply
4...3..2..1 ok ? it is important to observe the placement of these parts so that everything works... look at the drawing
(Edited)
0
Reply
Replying to @BHMarten
yes thanks. i noticed and commented on it right after.
thanks for the answer non the less
0
Reply
I got the correct screws but whenever I try to put them in the just fall out did I print it to big or am I supposed to have nuts for the screws?
The designer has replied
0
Reply
As described in the instructions.. M3 nut 16x
0
Reply
Boosted
盒子挺漂亮，就是不知道为什么作者首层的层高要设置成0.4，很容易让模型翘边，其他都很好
The designer has replied
0
Reply
hello, thanks for the feedback.. yes it's a mistake, the first layer should be 0.24 , I fixed it.
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share AlikeRelated Models
© 2024 MakerWorld