Sunlu S1 S2 Desiccant Tub Dryer by RockChewer

RockChewer

3D Printer>3D Printer Accessories

Print Profile(3)

All

X1 Carbon

P1S

P1P

X1E

0.24mm layer, 6 walls, 50% infill

Designer

4.1 h

2 plates

4.6(17)

fix ;D 0.24mm layer, 6 walls, 40% infill [ABS]

3.2 h

1 plate

5.0(3)

0.24mm layer, 6 walls, 40% infill [ASA]

3.3 h

1 plate

5.0(3)

Boost

166

273

166

Released

Description

MODEL FIXED - USE DESIGNER PROFILE - Wasn't finding an easy to print model for ABS when looking for a desiccant drying tub for my Sunlu S1 dryer. This model utilizes no top or bottom layers and 50% triangle infill, along with diamond holes on the sides and bottom, to maximize moisture release. Enjoy!

Comment & Rating (47)

@stromdc650

The print profile is no longer public

Una de las piezas se ha impreso mal

The designer has replied

@RockChewer

looks like you have a partial clog. Did you use ABS? it’s not a model problem. please calibrate your filament and print settings. thank you for giving it a go and I hope you can get success. if you would like pictures of my settings please let me know.

@jobuc1966

Replying to @RockChewer :

Das Problem ist ein anderes, Wenn Du auf Objekte gehst, erkennst Du das die Wandlinien für das rechte Bauteil, auf der Platte, auf "0" steht. stell den Wert auf "8" und Du wirst sehen das es klappt.

(Edited)

@Zoobert

Replying to @RockChewer :

It's not a partial clog - the slice even shows it to be printed that way, and a few other folks also get it (myself included). You'll see in my review i show the sliced object.

(Edited)

@Zoobert

The print profile is no longer public

I'm not at it now (so phone screenies atm) , but watched it halfway through - using ASA, and it was coming out great and clean. I'll upload a final pic once it cools down and I put it together. The second piece came out weird (sending it via makerworld/handy). Loaded it in BStudio, and it shows it being weird in the print, too - using the downloaded profile. Not sure what's causing it. Still works fine, glued them together - and structurally will be fine. Just something about the sides of that one in the print profile. Probably wanna sort that before too many folks print this with the funky second half.

(Edited)

The designer has replied

@Traumlewis

had the same problem, I uploaded a profile that fixed the error. and is faster to print.

(Edited)

@RockChewer

I really appreciate the comment and photos. What I discovered is that the Orca Slicer file was not converted properly, as it would have been with Bambu Slicer. Thank you for bringing this to my attention... also for some reason I am not getting notifications when I get messages, so pardon the delay. - Corey

@RockChewer

Replying to @Traumlewis :

I really appreciate the comment and the revised profile. What I discovered is that the Orca Slicer file was not converted properly, as it would have been with Bambu Slicer. Thank you for bringing this to my attention... also for some reason I am not getting notifications when I get messages, so pardon the delay. - Corey

(Edited)

@user_4277520780

Habs in ABS gedruckt, ging wunderbar, nur leider passt es in den S2 nicht perfekt, der Abstand der Rollen im S2 scheint ein andere wie im S1 zu sein. Aber egal ist trotzdem nutzbar.

@smashd

Print Profile

0.24mm layer, 6 walls, 50% infill

won't fit the two rods inside of my S2, doesn't matter too much though, probably another revision than the uploaders

(Edited)

@Jp3dPrint

Print Profile

0.24mm layer, 6 walls, 50% infill

tres bon fichier ... merci

@Hiosdra

Print Profile

0.24mm layer, 6 walls, 50% infill

The designer has replied

@RockChewer

Thanks!

@cristiano_melon

Print Profile

0.24mm layer, 6 walls, 40% infill [ASA]

@Ellinas71

Print Profile

0.24mm layer, 6 walls, 50% infill

(Edited)

@motoyuki85

Print Profile

0.24mm layer, 6 walls, 50% infill

Would prefer if the sides had tabs to snap together.

The designer has replied

@RockChewer

I hear what you are saying, but why leave 4 stars? was there something wrong with how it printed? I appreciate the feedback.

@motoyuki85

Replying to @RockChewer :

it printed fine. The 4 stars is because it is good, but not all the way there. Friction fit tabs would be great but at the very least, a note in the description so people know they'll need some CA glue or other suitable adhesive for their print to be functional.

@DustyKnuckles

Print Profile

0.24mm layer, 6 walls, 50% infill

a little narrow, but fits well and no leaking from the vents!

The designer has replied

@RockChewer

thanks! wanted to keep room on the sides for convection, I have a blower installed in mine which is a mod from a couple years ago. if you want one wider just let me know :-)