Ultimate Filament Clip Clamp by jajaum3d

jajaum3d

3D Printer>3D Printer Accessories

Print Profile(10)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

5 clips, 0.12mm layer, 2 walls, 15% infill

1 h

1 plate

4.4(18)

A1 x3 0.2mm layer, 2 walls, 15% infill

32 min

1 plate

4.5(6)

1 clip, 0.12mm layer, 2 walls, 15% infill

21 min

1 plate

3.9(7)

1 clamp, 0.2mm layer, 3 walls, 15% infill

18 min

1 plate

5.0(1)

Click to see more

Boost

123

284

256

Released

Description

🌟 Support My Work & Unlock Exclusive Benefits!🌟
Become a patron on Printables.com and gain access to early releases, commercial licenses, and more.

See all my designs on cults:
https://cults3d.com/en/users/jajaum3d/creations

All my designs are protected by Copyright Law. Purchasing does not grant the right to sell any digital file or printed model of my designs without explicit consent. Please respect the hard work of 3D artists by never sharing or selling digital files.

After using lots of the options available, I needed to make one.
The clamp type is my favorite because those in a single piece stresses the PLA and after some time the filament breaks.
Added a grip at the tip of the screw that rotates freely and firmly hold the filament in place, the curved outside gives strength and uses less filament.

The file is in STL and in the best orientation.
0.2mm layer height, 3 walls and 0% infill will give you a strong useful piece.
Twist the grip to make it loose and rotates freely.

Comment & Rating (40)

@Bas7ard

Print Profile

5 clips, 0.12mm layer, 2 walls, 15% infill

impressive! best filament clip ever

@mangesysleren

Print Profile

5 clips, 0.12mm layer, 2 walls, 15% infill

Had some problems with the clamp body getting loose on the first attempt. Second attempt with a brim went flawless.

@HBUnited

They work great and have not failed to hold my filament in-place yet. Used Bambu Basic PLA Green

@MasterGadget64

Print Profile

A1 x3 0.2mm layer, 2 walls, 15% infill

Bed Adhesion Issue:Need to add a brim.

@rikke1992

best screw clamps I've tried

@serranojosea1

Print Profile

5 clips, 0.12mm layer, 2 walls, 15% infill

OMG. Where were these after all the filament wasted on the ones I tried before. Printed in Bambu PLA and came out nice. Thanks for the share!

@vdubb

Print Profile

A1 x3 0.2mm layer, 2 walls, 15% infill

PLA is not the best for these

@brunotome1

The print profile is no longer public

Well Done Great job

@armoth1

Print Profile

5 clips, 0.12mm layer, 2 walls, 15% infill

prints super nice, thread is very well designed and the screw starts easily. Only downside is the slot for the filament being in the screw so it rotates when you are tightening it and sometimes makes aligning the filament properly quite tough. The best screw type filament clamp I ve tried to date though

@jajaum3d

It seems there might be a misunderstanding. The tip of the clip is intentionally designed to rotate freely to prevent the filament from twisting. After printing, you simply need to twist the grip to break it free, allowing it to rotate as intended. If it's too tight you can try using pliers and gently twist it a little bit side to side, and it should come loose without breaking.

(Edited)