Modular Desk Drawer (Stackable Desktop Organizer)

Copyright Claim

Modular Desk Drawer (Stackable Desktop Organizer)

Boost
182
320
33

Print Profile(5)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

[Frame] 0.2mm layer, 2 walls, 15% infill
[Frame] 0.2mm layer, 2 walls, 15% infill
Designer
7.1 h
1 plate
5.0(7)

[Drawers] 0.2mm layer, 2 walls, 15% infill
[Drawers] 0.2mm layer, 2 walls, 15% infill
Designer
16.7 h
6 plates
5.0(5)

[Joints & Hooks] 0.2mm layer, 2 walls, 15% infill
[Joints & Hooks] 0.2mm layer, 2 walls, 15% infill
Designer
43 min
2 plates
5.0(1)

[Optional Bases] 0.2mm layer, 2 walls, 15% infill
[Optional Bases] 0.2mm layer, 2 walls, 15% infill
Designer
3 h
2 plates
5.0(3)
Click to see more

Boost
182
320
33
6
353
96
Released

Description

Minimalist Desktop Drawer

Fully Configurable, place on your desks, dressers, shelfs, always suits your needs.

 

Multiple Frames can be endlessly connected, horizontally, vertically, or both ways.

5 Different Drawers, 2 Optional Cabinet Bases, 2 size of Hooks and more to come.

 

Frame Size: 129x123x204mm

Draws Size: 124.8x45.5x203mm

Print guideline:

  • Print one or more frames, you can use 0.24 layer height to reduce print time.
  • Print numbers of draws you like, you can print 2 draws in one plate.
  • Print cabinet bases (optional) and joints for final assemble.
  • Try different color combinations to show off your personality.
  • For certain materials, it seems like a good idea to add a brim out of caution.

PS: Due to different materials and printers, the tolerances may vary slightly. If the frame assembly is getting too tight, you can lightly sand the parts as needed. In my personal opinion, it's better to be tight than loose.

 

极简设计的桌面抽屉

完全可定制化,框架可以横向或纵向或组合拼接,以适应各种不规则空间,五种不同内分割的抽屉,可满足不同需求。

Comment & Rating (33)

Please fill in your opinion
(0/5000)

Boosted
The bases were a real beast to get on.. I will use singles if I ever need to print more of these. Otherwise, they are awesome and have created a great solution for my miniatures painting area!
The designer has replied
0
Reply
Looks great! Do you mean the bases are a bit too tight? I'm thinking of adding a version with slightly bigger tolerances. Thanks for the review.
0
Reply
Tolerances are quite tight. Even with lubrication, getting the shells to fit together can be difficult.
The designer has replied
0
Reply
I apologize for the inconvenience. Due to different materials and different printers, the tolerances may vary slightly. In my personal opinion, it's better to be tight than loose. You may be able to slightly sand it down, and I will also add a reminder in the introduction. Thank you for pointing out this issue.
1
Reply
Replying to @qiqiji :
I'm using an X1C, and printing in PLA-CF which keeps the tolerances tight. As a note, I just printed the dual base and they're pushing each other apart.
0
Reply
Replying to @morrow :
Print one or two connceter from third profile to link two frame together.
0
Reply
Print Profile
[Frame] 0.2mm layer, 2 walls, 15% infill
first part came out nice so far ! I did have to add a brim as I was having one corner peel up on two separate occasions but the brim did the trick as well as turning off the aux fan
The designer has replied
0
Reply
Glad you managed it out. For certain materials, it seems like a good idea to add a brim out of caution.
0
Reply
I used Kexcelled PLA K3 for the frame and PETG-CF for drawers, not run into any adhesion issues, I will add a note in the description. Thanks again.
0
Reply
Great Design. Can you please add a drawer without any dividers?
The designer has replied
0
Reply
Sure thing! [Drawers] Profile updated, Happy to help out!
0
Reply
Print Profile
[Optional Bases] 0.2mm layer, 2 walls, 15% infill
Tip top
0
Reply
Print Profile
[Frame] 0.2mm layer, 2 walls, 15% infill
Tip top
0
Reply
i can't see any problems, but I want to ask anyway. is there any problem with upscaling?
0
Reply
Boosted
Print Profile
[Optional Bases] 0.2mm layer, 2 walls, 15% infill
Difficult to insert but with lubrificant it works😁👌👍
0
Reply
Boosted
Print Profile
[Drawers] 0.2mm layer, 2 walls, 15% infill
Excellent 👌
0
Reply
Boosted
Print Profile
[Frame] 0.2mm layer, 2 walls, 15% infill
Perfect !! Thank u !! 🙏
0
Reply