Bambulab P1P/P1S/X1C Small Poop Chute Bin with Magnet
Copyright Claim
Bambulab P1P/P1S/X1C Small Poop Chute Bin with Magnet
Boost
74
127
91
Print Profile(2)
Circular magnet 0.2mm layer, 2 walls, 20% infill
1.7 h
1 plate
Rectangular magnet
1.7 h
1 plate
Boost
74
127
91
4
744
830
Released
Description
Because all of the listed Poop Bins were too big for me, i created a small but effective one.
Holds probably about ~20 Poops?! Have not tested the maximum capacity yet, but without the AMS this should last me a while ;)
Two little nose for easy alignment included ;)
I've made two Versions of it.
- Poop_Chute_Rec10x5x2 for a rectangular magnet Size 10x5x2mm
- Poop_Chute_Cir10x2 for a circular magnet with a Diameter of 10mm
Magnets have to be glued in after
Comment & Rating (91)
All
Print Profile
Circular magnet 0.2mm layer, 2 walls, 20% infill
schön und dezent, pla silver (silk)
wie in der Beschreibung zu lesen: für große multicolor Drucke zu klein - Verstopfungsgefahr - schneller Tausch durch die Magnete aber kein Problem
genau der richtige für mich!!
(Edited)
1
Reply
schaut sehr gut aus :) vielen Dank für deinen Kommentar
0
Reply
Print Profile
Circular magnet 0.2mm layer, 2 walls, 20% infill
great size for someone who doesn’t produce a mega lot of Poop! modified slightly to add ‘POOP’ logo!
1
Reply
Nice design - much quicker to print for those of us that only produce a little poop! I added a 'POOP' logo to mine!
1
Reply
Print Profile
Circular magnet 0.2mm layer, 2 walls, 20% infill
the container is smaller than most but perfect for me since I only print as a hobby. I didnt want a large container that took forever to print. The print quality is excellent. I added the magnets and it attached perfectly to my P1P. Couldnt be happier!
1
Reply
Awesom, thank you for your Kind Feedback :) Glad you like it.
0
Reply
Print Profile
Circular magnet 0.2mm layer, 2 walls, 20% infill
Looks great. Really strong (esun PLA Silk). Only issue I had revolved around supports. Bambu studio suggested I use supports, and as a newbie to the 3D printing world, I enabled them. It took forever to go through each joint and remove them. A friend of mine told me I should have not enabled them. Maybe someone on here can confirm/deny?
1
Reply
hey, i can confirm you dont need supports for this model. just make sure you slow down on the overhangs in the slicer and it will print Fine
0
Reply
Boosted
Print Profile
Circular magnet 0.2mm layer, 2 walls, 20% infill
Perfect. Can print without support.
1
Reply
Print Profile
Circular magnet 0.2mm layer, 2 walls, 20% infill
Perfect for me
1
Reply
Print Profile
Circular magnet 0.2mm layer, 2 walls, 20% infill
Printed in green Bambu pla. It turned out great. doesn't take up much room and it's easy to remove for emptying.
1
Reply
Print Profile
Circular magnet 0.2mm layer, 2 walls, 20% infill
Filament got tangled print continued to go without warning print failed with only the bottom section of the print complete
0
Reply
Sounds More Like an User/Printer error than a design or profile error to be honest :)
thanks anyway for your feedback
(Edited)1
Reply
Print Profile
Circular magnet 0.2mm layer, 2 walls, 20% infill
works great
1
Reply
License
This work is licensed under a
Creative Commons Attribution-NoncommercialRemixes (3)
Click to see more
Related Models
© 2024 MakerWorld