ERGONOMIC + Easy click wireless mouse cover by FADY

FADY

Hobby & DIY>Electronics

Print Profile(5)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

WITHOUT BAMBU LOGO

Designer

2.8 h

1 plate

4.7(65)

WITH BAMBU LOGO ON THE TOP

Designer

2.8 h

1 plate

4.6(32)

0.12mm layer, 2 walls, 15% infill

5.2 h

1 plate

5.0(1)

More supports below mouse buttons, PLA-CF

3 h

1 plate

3.5(2)

Click to see more

Open in Bambu Studio

Boost

581

717

175

1.8 k

691

Released

Description

REMIX FROM BAMBULAB'S WIRELESS MOUSE
REQUIREMENTS LIST:

Mouse Kit 002 from BAMBULAB :

http://store.bambulab.com/products/wireless-mouse-components-kit-002

Bottom Part:

https://makerworld.com/en/models/13716#profileId-14573

1/ added extrusions from both sides of the mouse for better handling

2/ increased bottom surface for more stability when pressing the buttons

3/ Easier to click right button

4/ with tree supports (also printable without supports)

5/ with brim

Ergonomic mouse cover for the wireless mouse from bambulab

Bill of Materials

Bambu parts

Wireless Mouse Components Kit (1pcs)-002

MH002

× 1

Purchase from Bambu Store

Comment & Rating (175)

@Cado

Print Profile

WITHOUT BAMBU LOGO

Strength Issue:I used the standard profile for the a1 mini. Unfortunately, the error occurred in the same place both times. The left mouse button keeps clicking backwards when the nose moves over it. I cleaned the print bed again on the second attempt. Unfortunately the same again

The designer has replied

@fady

enable flow calibration. you might have over extrusion that causes extra pla to flow. calibrate the flowrate with bambustudio and enable flow calibration in the beginning of the print. i hope this helps

@bluepineapple

Exact thing happens to me when printing these mice. I painted on additional supports. One lower down the button pad and one near the breaking point. Keeps the two buttons still during the print and worked perfectly

(Edited)

@Cado

Replying to @bluepineapple :

Would you please share your file? Maybe you can share it as a print profile with this model?

@PMMzero

Boosted

Print Profile

WITH BAMBU LOGO ON THE TOP

Printed on X1C, but printed great with all other settings the same.

The designer has replied

@fady

i appreciate it very much

@MrGnarly

Boosted

Added a ABS profile with scarf joint settings. works well, could possibly use a small wing for my pinky

@noseeam

Does not fit bottom perfectly but besides that good stuff.

The designer has replied

@fady

what's the problem exactly? is it loose or tight?

@fady

i assume because you printed it horizontally and not standing that it wasn't perfect for the fit

@psychoelf

Does your design fix the flaw in Bambu's? Specifically to the left middle of the scroll wheel? I don't see that defect in any of these photos. I've printed 4 of the Bambu V2's and only one came out without the defect. NOTE: This picture is the Bambu V2, NOT this current model.

(Edited)

The designer has replied

@fady

as you can see with the makes of the users that defect does not appear in my model.

@psychoelf

Replying to @fady :

That's what I concluded as well and printing is underway. Thank you for responding! I believe it had something to due with Bambu's tree in the actual model.

(Edited)

@fady

Replying to @psychoelf :

i never experienced that failure in the mice i printed but good luck with the print nontheless. dont forget to wash the bed of the printer now and then, and share your print here when finished!

@jamesarmstrong3

Boosted

Printed nicely in Burnt Titanium filament. Base was printed in Rino Co-polyester. 0.08 layers.

The designer has replied

@fady

it looks soo gorgeous in this color

@user_3613789333

Print Profile

WITHOUT BAMBU LOGO

Halfway up it started to spaghetti

The designer has replied

@fady

wash the build plate

@user_3613789333

it did fine until layer 344. at top. The prince did not slip it just started spaghetti.

@user_3613789333

Replying to @fady :

The print did not slip it just started spaghetti at layer 344

@user_4025874114

Boosted

Print Profile

WITH BAMBU LOGO ON THE TOP

didnt have any issues printing this model. comfortable on the hand when using

The designer has replied

@fady

perfect tell me if you find anything bad in the grip

@theokk311

Print Profile

WITHOUT BAMBU LOGO

printed twice and had the same quality issues both times. weird ripple effect on both buttons in the same areas.

The designer has replied

@fady

i do not suggest you reprint it staight away but i think it's an arteffect from either using arachne or not! try to print only that part of the mouse that has that issue without the setting! if not then it might be a slicing error.

@theokk311

Replying to @fady :

It seems to be because arachne was not being used. Good call. I did some research last night and tried it. It is still showing on the right button but not as much.

@user_925576689

Because I love obnoxious colours...