BambuLab AMS Silica Gel Box With Hygrometer - Full Set Remixed by giuliolibrando

Remixed by

giuliolibrando

3D Printer>3D Printer Accessories

Print Profile(5)

All

X1 Carbon

P1S

P1P

X1E

NEW - 5 Pieces - 0.2mm layer, 2 walls, 15% infill

Designer

7.8 h

3 plates

4.7(367)

NEW - 3 Pieces - 0.2mm layer, 2 walls, 15% infill

Designer

5.3 h

1 plate

4.7(95)

NEW - 5 Pieces - 0.12mm layer, 2 walls, 15% infill

Designer

11.2 h

3 plates

4.7(32)

Box small left alone

1.7 h

1 plate

4.9(25)

Click to see more

Boost

621

1184

626

3.4 k

4.8 k

Released

Description

BambuLab AMS Silica Gel Box With Hygrometer - Full Set of 5 boxes

The project comes pre-oriented on the build plate. No supports are required when printing the pieces.

The hygrometer/thermometer just clicks in place.

If you want an accurate reading do not fill with silica the central one with the sensor.

-----------------------

It's available a variant of this model that use a different hygrometer sensor.

You can find it here:

BambuLab AMS Silica Gel Box With Mi/Xiaomi Hygrometer - Full Set

-----------------------

Hardware:

You will need this hygrometer

The plates are divided by box type:

01 - One large central box with humidity sensor/thermometer
02 - Two large boxes
03 - Two small boxes for the sides (optional)

Assembly Istruction

Insert the side panels into the central box by sliding them into the grooves
slide the cover on the panel tracks until it bottoms out

“”"Installation"""

---

N.B. Do not remove the Object Modifiers from the plate 03

Comment & Rating (626)

@P4rad0x

Print Profile

NEW - 5 Pieces - 0.2mm layer, 2 walls, 15% infill

works perfect

The designer has replied

@giuliolibrando

Thank you for your feedback!

(Edited)

@soepie1

did you use support?

(Edited)

@P4rad0x

Replying to @soepie1 :

no I just loaded the profile and started printing

(Edited)

@Dennis527

Print Profile

Box small left alone

great print. fits well

The designer has replied

@bollekeil

awsome! Thank you :)

@Dennis527

Print Profile

Box small right alone - 0.12mm layer, 2 walls, 15% infill

great fir. very nice print

The designer has replied

@bollekeil

thank you 🥰 Looks good!

@JVJV

Edit: I feel like there is a flaw in this design that the other desiccant boxes elsewhere don't have. This one has the side loading drawers that can fall out when standing upright. Its hard to stay locked and can just open up on its own. I just lots a TON of desiccant all over the floor. I feel like having it load from the side, particularly where the door loads from the bottom not the top means gravity can open the door easily. I am going to go with the top loading versions. If you wanted to update these design you could simply have the door slide come from the top. Previous Comment: Works pretty well I just have issues with sliding locks not locking on all the boxes. This could depend on filament used but a simple fix would be to just thicken the bump on the lock. It should provide a better lock for everyone even those where it works okay. I can update it if the original creator can provide the fusion files. Also you can simply add it yourself inside the slicer. Thanks for the great file.

(Edited)

@HardwareMaster

Yeah I have the same issue, it slides down when I try and take it out. It needs to be improved. Maybe using a little tape until then will solve the problem.

@JVJV

Replying to @HardwareMaster :

I just had a major mess caused by this coming out when I took them out. Never again with these!

@SirPasserati

perfect, thank you!

The designer has replied

@giuliolibrando

You're welcome! The small boxes are inverted, it will fit better if you swap them place

@jbedoya_3d

Print Profile

NEW - 5 Pieces - 0.2mm layer, 2 walls, 15% infill

Nice and clean, easy to print with great results. See my comments below [updated thisnpost becsude initially I mistake the photo mostly] printed yours, single color, overture PLA, no changes in the std parameters predefined i liked a lot because the size of tbe grid is much more apropriste for the dry dry orange indicating silica that i have as it does not allow any small pellets to fall out I found the boxes very sturdy and essy to fit in the AMS. the tolerances to assemble the boxes were very tight (I sanded just a bit couple of the fitting borders), but that tight tolerances most probably is what make this boxes feel very sturdy. definitively loved them thanks

(Edited)

The designer has replied

@giuliolibrando

Well, thanks but it's not mine the model in the picture

@jbedoya_3d

Replying to @giuliolibrando :

apologies for that, I also printed yours, single color, overture PLA, no changes in the std parameters predefined i liked a lot because the size of tbe grid is much more apropriste for the dry dry orange indicating silica that i have as it does not allow any small pellets to fall out I found the boxes very sturdy and essy to fit in the AMS. the tolerances to assemble the boxes were very tight (I sanded just a bit couple of the fitting borders), but that tight tolerances most probably is what make this boxes feel very sturdy. definitively loved them thanks

@VJPPEREZ

Boosted

Print Profile

Box small left alone

perfecto A+++++

@cleeb1983

Print Profile

Box small left alone

perfect

@NeoBlack

Boosted

Print Profile

NEW - 5 Pieces - 0.2mm layer, 2 walls, 15% infill

A very clean and precise print, the missing Hygrometer will be delivered on Monday. I am very happy with the result. Great job from the designer. Thank you!