Poke-Monster Keychain Pack #44 Browt Pombon Gecqua

Search models, users, collections, and posts

Powerpill.prints

Toys & Games>Characters

IP Report

GIF

Print Profile(1)

All

A1 mini

P1P

H2D Pro

X1 Carbon

H2C

H2S

H2D

X1E

P1S

P2S

X2D

A2L

0.28mm layer, 1 wall, 15% infill

Designer

2.9 h

3 plates

5.0(2)

Open in Bambu Studio

Boost

114

Released

Description

🌱🔥💧 Pack #44 introduces the Gen 10 starters!

Pombon, Gecqua, and Browt! This release introduces a brand-new generation of characters reimagined in the signature chunky retro pixel-art style used throughout the series, designed to work beautifully as 3D prints, keychains, display pieces, wall art, and collectible gaming décor.

• Pombon – A lively and cheerful starter full of playful energy, bringing bright personality and charm to the lineup.
• Gecqua – Sleek, clever, and agile, this starter moves with calm confidence and sharp instincts.
• Browt – Solid and determined, Browt brings powerful presence and grounded strength to the trio.

These three characters represent the start of a brand new generation, blending modern designs with the nostalgic pixel-art style that runs through the entire series. Their strong silhouettes and expressive poses make them perfect for retro gaming fans, collectors, pixel art lovers, and 3D printing enthusiasts looking for standout models to print and display.

Whether you're building keychains, shelf displays, gaming room décor, or collectible prints, Pack #44 adds fresh generation excitement while fitting seamlessly alongside previous character packs and TCG-style releases.

As always, this project continues to grow thanks to the community — your boosts, feedback, and ideas help guide what comes next. A new generation begins here. 🌱🔥💧

This pack has been all set up for super simple and easy printing with the AMS or AMS lite!

All the models are set to 4 Colours! Just load your filament, slice and go!

Membership

🍄 "READY TO POWER UP? 🚀 with a membership for our retro video game keychain packs! No cheat codes needed—just pure pixel-perfect prints! 🔥 With this membership, you’re stepping back into a world where cheat codes were sacred, cartridges needed blowing, and every pixel mattered! ⚡💊

Join

Boost Me (for free)

If you enjoyed these keychains, please consider boosting to support the creator. Thank you and make sure to check out my other packs!

Most keychains take between 45 minutes to 1.5h to print!

Special thanks to Gen2Sprites for permission to use his pixel-artwork for these keychains!

Check out My other Poke-monster style Packs here:

All models have been test printed on the A1 Mini with the AMS Lite!

I have this set to use the 0.4mm nozzle with a .28mm layer height. This prints three layers of colour so the colours turn out nice and saturated and minimize waste. After the colour, there's one solid black layer, three layers of infill, and four final solid layers for the back for strength with the back pattern set to Hilbert Curve for a nice texture. There is a small hole in each model which is just large enough to fit a 1mm keychain jump ring. If you find it too small, you can modify the size of the “Keychain hole” object in BambuStudio to make it a little larger, or take a small drill bit and drill the final keychain to make it a little bigger!

I purchased my keychain set from Amazon if you'd like to get something similar!

All models have been flipped face down on the print bed so the surface texture from the PEI plate gives them a nice textured surface! All the different pieces of the models are there if you want to play around with it. There is one black ‘back’ piece in each keychain, which is perfectly aligned to the rest of the model. This causes some flickering in the viewport when moving around, but it disappears after slicing. If you modify the settings of that piece, it will affect the infill settings, so if you want to save a little filament, feel free to adjust it there!

I made some changes to the first layer and first layer infill speeds, reducing them both by about half. This increases the print time for the first layer, but increases the bed adhesion and print quality a bit. If you find that the first layer is printing too slow for your liking, feel free to reset them both back to default settings in the speed tab.

If you want some extra crisp pixels, you can try printing these with the 0.2mm nozzle, but I didn't think the increased print time was really worth the extra quality. It's definitely noticeable, but I didn't think the tradeoff was there. Feel free to experiment and try it yourself!

Want to remove the keychain hole? No problem! Each keychain has a “Keychain hole” object on each plate. Just select it, delete it, and re-slice!

Want to scale these up really large to make some wall art? Just delete the “Keychain hole” object, then scale the X and Y axis to fit your print bed. Keep the Z-Scale back to 3.08mm so you're not printing extra layers though!

If you notice any settings that could be changed or improved, please let me know! I'd love to make any adjustments necessary so they all print great! If there's any other packs or characters you want to see, leave a comment!

Hope you Catch, er, Print them all!!

Like this pack? Check out my other video game keychain packs here:

Comment & Rating (7)

License

If you want to use this model commercially, please join my membership.

Join Now

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.