SUPER AMS Lite Spool Enclosure by Supergrapher

Supergrapher

3D Printer>3D Printer Accessories

Print Profile(5)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

Enclosure Base

Designer

13.9 h

5 plates

4.6(46)

Enclosure Cover

Designer

7.1 h

5 plates

4.6(13)

Enclosure Cover - with Hygrometer

Designer

9.9 h

8 plates

4.1(14)

PETG 0.2mm layer For Xiaomi Hygrometer 2

10.2 h

7 plates

4.0(1)

Click to see more

Open in Bambu Studio

Boost

432

880

198

962

608

Released

Description

Update:

I've created a new version taking in all the suggestions and feedback, check it out here

https://makerworld.com/en/models/486153#profileId-398821

I'll keep this version available for those who need a simpler solution or need to print replacement parts.

Keep your filamant dry with the SUPER AMS Lite Spool Enclosure!

The major advantages of the enclosures are…

Lightweight
Easy to print (No support needed)
Requires minimal additional parts (only a PTFE tube and connector)
Compatible with the Bambulab AMS Lite Top Mount
Option for adding your own Hygrometer

Instructions

Install the spool support, this prevents the enclosure from sagging.

Install pneumatic connectors(6mm) with 10 cm of PTFE tubes.

Install your filament.

Click the enclosure into position.

Insert dessicant packs into the side pockets.

All Done!

Comment & Rating (198)

@diyfather

Print Profile

Enclosure Base

very nice design, fortunately my bed is not big enough so i split the print into part. some hot glue and positioning the split do the trick. Good work realy helpful for me.

(Edited)

@rand

Hi, please share the model

(Edited)

@bbrunners

please upload the profile so I can easily print on my A1 mini 🙏🙏🙏

@TriforceLegend

Has this version been shared?

@adooley1684

Print Profile

Enclosure Cover - with Hygrometer

Lids can be a chore to get on at first but seem to get easier over time. Had issue where I'd constantly get a filament load error but it seems this was due to the PTFE tube extending too far out of the enclosure. Pulled it back some and haven't gotten the error again. Still would recommend extending the height of the upper bearing surface as the enclosure doesn't always stay fixed when filament is retracted.

(Edited)

The designer has replied

@Supergrapher

Do you mean extending this distance? so that it is closer to the AMS?

@adooley1684

Replying to @Supergrapher :

No, I haven't had the issue in a while but I meant extending the surface that bears into the feeder to ensure no chance of slipping. Included a picture below.

(Edited)

@Supergrapher

Replying to @adooley1684 :

ah, I see I did extend it abit in the later version, I’ll monitor to see if I’ll need to extend it again.

(Edited)

@ondrovic

Started print only thing I did was switch to PETG which is calibrated, and since I don't have an A1 using X1. Didn't do that great.

The designer has replied

@Supergrapher

I've tested on both PLA and PETG which works for me, but it does seem that there are more complaints when printing with PETG.

(Edited)

@ondrovic

Replying to @Supergrapher :

Yeah it managed to work fine when done in PLA Do you have a link for the 6mm threaded connectors?

@Supergrapher

Replying to @ondrovic :

I have no affiliation to the seller, just to show you which one to get. It is the PC4-M6 stainless steel version. https://www.aliexpress.com/item/1005004437566034.html?spm=a2g0o.productlist.main.1.2b2bc810mfgQ1Q&algo_pvid=4e58e27b-b2fe-4fe1-8aea-6cbdfb88234a&algo_exp_id=4e58e27b-b2fe-4fe1-8aea-6cbdfb88234a-0&pdp_npi=4%40dis%21SGD%212.68%212.42%21%21%211.94%211.75%21%402103244b17096336193116161ed25b%2112000029180298198%21sea%21SG%211678788008%21&curPageLogUid=KJL5sgX8KJ44&utparam-url=scene%3Asearch%7Cquery_from%3A

@IGiveMemes

Hello Supergrapher, I'm pretty new to 3d printing but I did model a container that holds dessicant for this dry box. Of course, It is meant only for the one side of the container that has the biggest pocket but I'm sure you could cut my container in half to fit the other side. I'll add a picture of it here. The lid is realtively loose so I opt to throw a little scotch tape on the side to make sure it doesn't spill. It's also heavy enough that it forces the dry box to turn all the way up. Holes are 1.1 diameter so it will fit most dessicant. If it is okay could I upload this?

The designer has replied

@Supergrapher

Looks good! go ahead!

@IGiveMemes

Replying to @Supergrapher :

Awesome, thank you!

(Edited)

@user_2097678733

did you post your version?

@Zamby3d

nice project...you could also add a hole for the sensor

The designer has replied

@Supergrapher

Got it! I should be able to add one to the cover

@Supergrapher

Updated with new cover for hygrometer.

@zagitariuz

Hi thankyou fir creating this!, cant print on a1 mini, thank god it fits on my mk4, i tried other dry box, doesnt fit on my mk4. I have questions about pneumatic connector, can give specific size? what size the thread? what size is the whole for ptfe, measured bambu ptfe is average 4mm, and the thread hole on the drybox is roughly 5.5mm, so is it pneumatic connector 4mm ptfe and 6mm thread?

The designer has replied

@Supergrapher

The connectors are 6mm, with 4mm PTFE tube passthrough,

@Supergrapher

Please leave a rating for the cover to bring it back up to 4 star :)

@ToyDD

Print Profile

Enclosure Base

i love the idea to use transparent filament

(Edited)

@FSfd4cmn9kqb

Boosted

why is there a big “1” and a small “4” ?

@ToyDD

Replying to @FSfd4cmn9kqb :

because they indicate the position of the AMS feeder unit

@KanoaN

气密似乎不太完美，湿度还是高达4-50%这还是有放乾燥剂的情况，（南部海岛气候，室外55-65%），如果用米桶可以25%-20%，还有盖子不容易盖上且用几次比较容易裂开，用的还是PETG,而且线料卷不好换 The seal doesn't seem perfect, with humidity still as high as 40-50% even with desiccants used.(live in the southern island, outdoors usually 55-65%). Using a rice barrel can keep it under 25%-20%. Also the lid is not easy to secure and tends to crack after a few uses even print with PETG, and the filament spool is difficult to replace.

(Edited)

The designer has replied

@Supergrapher

Did you put any desiccants inside? 1-2 bags new bags should be able to lower it under ambient humidity. It prints best using PLA. To remove the spool, grab the edges with your fingers using 2 hands (Kung Fu Tiger Paw style), brace your thumb on against the spool holder and pull it out.

@rnmss

对对，我也是，今天外面60~70，米桶里30 (平时没这么潮可以到25%) ，这里面只能达到45% Me, too. I can only achieve 45% today (ambient 60-70), well the best seal I have can reach 25-30.

@dustydumptruck

Print Profile

Enclosure Base

I added a pass through adapter for those that didn't get pass through fittings and sometimes the lids are difficult to close but pretty awesome otherwise

@matteoleone

Print Profile

Enclosure Base

that’s very cool, would be nice to have a hole for an hygrometer :)

(Edited)

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.