Pill Shape Organizer (Customizable)

Copyright Claim

Pill Shape Organizer (Customizable)

Boost
43
45
12

Print Profile(4)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

2 Plates - 0.2mm layer, 2 walls, 5% infill
2 Plates - 0.2mm layer, 2 walls, 5% infill
Designer
2 h
2 plates
5.0(8)

Inserts - 0.2mm layer, 2 walls, 10% infill
Inserts - 0.2mm layer, 2 walls, 10% infill
Designer
43 min
2 plates
5.0(1)

TPU Seal - 0.2mm layer, 2 walls, 10% infill
TPU Seal - 0.2mm layer, 2 walls, 10% infill
Designer
8 min
1 plate

3 Plates - 0.2mm layer, 2 walls, 5% infill
3 Plates - 0.2mm layer, 2 walls, 5% infill
Designer
2.1 h
3 plates

Boost
43
45
12
1
163
178
Released

Description

Overview

This pill organizer is a print-in-place model and does not require additional hardware. Print the lid assembly and the base then follow the instructions below to assemble the model. The lid of the pill organizer has letters for the days of the week, allowing you to organize a week's worth of pills. This model is great for daily use or traveling.

 

Materials and Printing

Materials such as PLA or PETG are suitable for this model.

  • 2-3 walls
  • 5% infill
  • Support enabled (needed for base)

Optional Accessories

  • 7 Letters (in main print profile plate, STL of the lid with letters also available for AMS)
  • TPU Seal (see print profiles)
  • Inserts for additional customization (see print profiles)

Assembly

Required materials

  • Lid
  • Base
  • Super glue, epoxy, or hot glue
  • Cutting tool
  • Optional: 7 Letters
  • Optional: TPU Seal
  • Optional: Inserts

Instructions

  1. After finishing the print for the Lid, cut the indicated blue brim off the back hinges that were used to increase bed adhesion.
  2. Rotate the 3 Lid hinges to break them free. If it is difficult, try warming the part up using warm water to loosen the joint.
  3. Optional: Apply glue in the Lid letter cavity and glue the 7 Letters.
  4. Optional: Apply glue in the Lid grove and glue the TPU Seal in for an airtight seal.
  5. Apply glue in the Base hinge cavity at 2 locations. 
  6. Insert the 2 Lid hinge flanges into the Base.
  7. Optional: Place inserts
  8. All done!


Check out other models

Stackable Organizing Box

Print-in-place organizer

Pocket Sized Pill Case

3 day pill organizer

Lover Rover Kit

Valentines Mars rover

4 Way PTFE Splitter Adapter

AMS and external spool adapter

 

Comment & Rating (12)

Please fill in your opinion
(0/5000)

This printed great on a P1S. Thanks for sharing.
0
Reply
printed very well on x1carbon. scaled 120%. the hinge and locking clip are smooth and snug. good job. I'm also looking for a pill case with individual compartments (makes it easier to remove pills for use)
The designer has replied
1
Reply
Thanks for sharing! Does this pill case work for you? https://makerworld.com/en/models/173048#profileId-190103
0
Reply
Print Profile
2 Plates - 0.2mm layer, 2 walls, 5% infill
Came out great! Tolerances on the latching lid are a bit snug for me so had to open and reclose before getting it to be more easily opened
1
Reply
Print Profile
2 Plates - 0.2mm layer, 2 walls, 5% infill
perfect!
0
Reply
Print Profile
2 Plates - 0.2mm layer, 2 walls, 5% infill
1
Reply
Print Profile
Inserts - 0.2mm layer, 2 walls, 10% infill
1
Reply
Boosted
Print Profile
2 Plates - 0.2mm layer, 2 walls, 5% infill
0
Reply
Print Profile
2 Plates - 0.2mm layer, 2 walls, 5% infill
0
Reply
Print Profile
2 Plates - 0.2mm layer, 2 walls, 5% infill
0
Reply
Print Profile
2 Plates - 0.2mm layer, 2 walls, 5% infill
0
Reply