Dragon ornaments
Copyright Claim
Dragon ornaments
Boost
380
644
229
Print Profile(12)
0.2mm layer, 3 walls, 10% infill
Designer
3 h
2 plates
0.2mm layer, 3 walls, 10% infill
Designer
1.2 h
1 plate
60% scale, 0.2mm layer, 3 walls, 15% infill, with adaptive layer
1.5 h
1 plate
0.2mm layer, 2 walls, 10% infill
2.2 h
1 plate
Click to see more
Boost
380
644
229
48
2.5 k
1.6 k
Released
Description
2024.05.15 更新版/Updated version on May 15th, 2024
https://makerworld.com/zh/models/464371#profileId-373003
----------------------------------------------------------------------------------------------------------------
0.2层高 填充 10% 螺旋填充 无支撑打印
0.2 layer height filled with 10% spiral filling, unsupported printing
缩小尺寸避免悬垂可以适当调整外墙打印速度60-90区间最佳。
Reducing the size to avoid overhanging can be adjusted appropriately. The best printing speed for the exterior wall is in the 60-90 range
Dragon ornaments
以下为 降速90外墙效果（模型缩小了45%）
The following is the 90 degree reduction in exterior wall effect (the model has been reduced by 45%)
Comment & Rating (229)
All
Boosted
Scaled to 50% and works perfectly.
2
Reply
Boosted
Can you tell me the configuration to get the neck part right?
0
Reply
Boosted
I haven’t tinkered with the print settings, I’ve just hast to scale the eyes to 49 percent in order to fit them in the sockets. The neck and horns weren’t perfect but quite good.
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill
Beautiful. Our grandkids are going to love them. I used a tricolour pla silk+.
1
Reply
welches Filament ist das ?
(Edited)1
Reply
Replying to @frankschuppert
this is the filament I used.
0
Reply
This is a cute little print. printed it both in black and blue silk with no problem-
0
Reply
Boosted
Can you tell me the configuration to get the neck part right?
0
Reply
Replying to @IsMa07
Honestly i printed it with default settings generic PLA I bought as b-stock.
0
Reply
A1 mini
The designer has replied
1
Reply
眼睛装错了吧
0
Reply
Boosted
Top!!!
1
Reply
Print Profile
0.2mm layer, 3 walls, 10% infill
would benefit from some supports under the chin
The designer has replied
0
Reply
Partial consumables or external wall deceleration
0
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 10% infill
look good
0
Reply
Boosted
Can you tell me the configuration to get the neck part right?
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill
very cute, I just painted the eyes instead of wasting filament.
The designer has replied
0
Reply
Hi
Thank you for your comment, I put the multicolor profile for those who preferred not to have anything to paint, but the most economical is actually to take a few minutes to paint the eyes
0
Reply
Print Profile
60% scale, 0.2mm layer, 3 walls, 15% infill, with adaptive layer
sehr gut bis auf die Ohren, aber sehr schön, leicht nacharbeiten und schon super. Danke
1
Reply
Print Profile
0.2mm layer, 3 walls, 10% infill
great little dragon , lovely detail
(Edited)
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Share Alike
Related Models
© 2024 MakerWorld