Panda Touch Screen Fold Mount

Remixed by

Panda Touch Screen Fold Mount

Remixed by
Boost
236
377
156
GIF

Print Profile(2)

All
P1P
P1S
X1
X1 Carbon
X1E
A1

0.2mm layer, 3 walls, 15% infill
0.2mm layer, 3 walls, 15% infill
Designer
3.9 h
4 plates
4.9(121)

0.2mm layer, 3 walls, 15% infill
0.2mm layer, 3 walls, 15% infill
1.2 h
1 plate
5.0(1)

Boost
236
377
156
22
802
836
Released

Description

*** Link to v2.0 of this dock if you would rather use that design - https://makerworld.com/en/models/178613 (this will require magnets and replaces the need for the original magnetic dock) ***

 

Note: This design changes no stock parts on either the Panda Touch or the Bambu lab printer, this is just and additional mount to attach the Panda Touch to the printer.

 

*** Update like I have add on my V2 I have add a small hole for the full surround mount to allow access to push the buckle on the stock screen when you want to remove it in the future, this allows you to slip a small allen key through ***

 

 

*** Update I have added a new mount based on requests with a cable channel available on the other side and a stand off so stock screen buttons should not get pressed (unless you push down hard on the bottom right have corner) ***

 

Ever since I saw the new panda touch screen I though using @TeachingTech design would be a great addition and make your P1 printer look even more like the X1.

 

I have now update the design to have a cable channel in the mount so it does not bind on the screen when lowered.

 

I have also add on a different adapter that surrounds the screen to use this you will need to remove the screen and release the cable then install the mount and plug the cable back in. This mount will be more secure to the movement of the screen and is based on MorikoStyles design that i was using previously.

 

You will need some longer screws to attach the top two mounting points as the ones supplied are not long enough I used 6mm ones i had lying around.

 

Hardware

 

2 x M3 x 4mm countersunk bolts for attaching the bottom points to the charging dock. (these are the stock ones that come with the screen)

2 x M3 x 6mm countersunk bolts for attaching the top mounting points to the charging dock.

2 x M3 x 12mm bolts for attaching the enclosure to the adaptor.

 

Any other ideas shout and might be able to incorporate.

Comment & Rating (156)

Please fill in your opinion
(0/5000)

on the surround adapter there is an angle on the inside which does not allow the screen to sit flat which causes the screen clips on the left side back not to stick out far enough to connect it back to the printer Am I doing something wrong?
The designer has replied
0
Reply
no let me check this I altered this design to add a hole for access to the buckle let me check something didn’t get messed up due to that this morning
0
Reply
I have updated the raw STL and the print profile so all fixed now, not sure where that random shape came from but it appeared when i was altering the model the last time and never spot it.
1
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
works perfectly
The designer has replied
1
Reply
nice colour
0
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
perfect
The designer has replied
1
Reply
looking good
0
Reply
Printed great with the orginal settings! I didn't need anything fancy so just used random black pla
2
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
Tremendous model! Thank you!
1
Reply
i had mine mounted on the right side almost in front of the hole where the usb cable feeds through but i seen this an had to give it a try. thanks for sharing, fits perfect. shared pictures of where i had it an where its at now.
1
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
Great design and print profile worked perfectly
(Edited)
1
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
printed great, printed on one of the larger faces with small supports for bolt holes and tiny support for the indent. works perfectly and still holds it up despite the weight of the screen - when needing the access og screen.
1
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
Just what I was looking for!
1
Reply
Print Profile
0.2mm layer, 3 walls, 15% infill
hält mein Panda Touch super, habe es etwas angepasst, da ich meine Screenumrandung noch drauf habe.
1
Reply