Nintendo Switch Game Carousel
Copyright Claim
Nintendo Switch Game Carousel
Boost
853
1349
191
GIF
Print Profile(6)
2 Color Logo - Standard 0.2mm Profile
Designer
3.3 h
2 plates
No Logo - Standard 0.2mm Profile
Designer
3.1 h
2 plates
0.12mm layer - Multi-Color Logo
5.7 h
2 plates
0.2mm layer, 2 walls, custom infill
3.3 h
2 plates
Click to see more
Open in Bambu Studio
Boost
853
1349
191
43
1.6 k
1.5 k
Released
Description
*This project requires one 608 bearing*
There is a printable spring that adds a slight clicking sound when the carousel is spun. This is recommended, but optional.
As with any assembly that prints in multiple pieces and/or uses other components, actual clearances will be dependent on YOUR printer.
Print Settings
The Nintendo Switch logo in the middle of the carousel is designed to give you two options:
- If you have an AMS, MMU or similar product, the logo can be easily painted in the slicer
- If you do not paint it in the slicer, the logo will not appear at all
Assembly Instructions
- Insert a 608 bearing into the center of the base
- If you are using a spring, use a very small amount of glue to secure it into the hole as shown below
- Place the carousel on top of the base, ensuring that the gear tip drops into the center of the bearing
The filaments used in the pictures above:
- Bambu Lab Red Matte Scarlet Red PLA
- Bambu Lab Matte Charcoal PLA
- Bambu Lab Matte Ivory White PLA
Comment & Rating (191)
All
Print Profile
0.2mm layer - Multi-Color Logo
This is cool! I really like how clean this is and it’s very fun and functional as well. The only thing I added was a countersunk screw to keep the two sections locked together only because my kids are a couple of bulls in a fine china shoppe. Thanks
(Edited)
3
Reply
can you share how you added a screw without effecting the carousel effect?
(Edited)1
Reply
Sure, I drilled a small countersunk hole just big enough for the screw in the bottom plate. I made sure it was centered in the hole where the bearing sits. Then I put the top and bottom pieces together and drilled a small pilot hole in the center of the post and inserted the screw. Just be careful not to strip the screw you just need to get it finger tight so it stays snug in the post but still allows the top to spin. The smaller the pilot hole the better so the screw has something to bite and hold onto.
(Edited)1
Reply
Boosted
Print Profile
No Logo - Standard 0.2mm Profile
came out great following the designer default settings. I did assemble a logo onto the model to give to my niece.
2
Reply
Boosted
Print Profile
2 Color Logo - Standard 0.2mm Profile
wife loves it
1
Reply
Boosted
Print Profile
2 Color Logo - Standard 0.2mm Profile
love this and I also 3d printed the bearing
1
Reply
Boosted
Print Profile
2 Color Logo - Standard 0.2mm Profile
this is great for my kids to store their games
1
Reply
Boosted
Print Profile
2 Color Logo - Standard 0.2mm Profile
great design
1
Reply
Boosted
Print Profile
2 Color Logo - Standard 0.2mm Profile
perfektes Profil, super Qualität
1
Reply
Print Profile
2 Color Logo - Standard 0.2mm Profile
Good print profile and perfect function. My grandson was very happy about it ;-) THX
Filament: Sunlu PLA+ red/white, Sunlu PLA black matte
1
Reply
Print Profile
2 Color Logo - Standard 0.2mm Profile
Good Design, works good with Out AMS
1
Reply
Print Profile
2 Color Logo - Standard 0.2mm Profile
Eine tolle Aufbewahrungmöglichkeit für Nintendo Switch Spiele. Es funktioniert super, aber leider besteht keinerlei Verbindung zwischen dem ober und Unterteil, so dass man immer aufpassen muss, dass man das obere nicht anhebt. Ich denke, dass ein eingebaute Magnet, welcher den oberen unteren Teil miteinander verbindet, zu einer deutlichen Verbesserung führen könnte.
1
Reply
License
This user content is licensed under a
Creative Commons Attribution-Share AlikeRemixes (2)
© 2024 MakerWorld