Nintendo Switch 20 Game Holder & Carousel

Remixed by

Nintendo Switch 20 Game Holder & Carousel

Remixed by
Boost
255
582
149

Print Profile(2)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

With Logo v2 - 0.2mm layer, 4 walls, 15% infill
With Logo v2 - 0.2mm layer, 4 walls, 15% infill
Designer
4 h
2 plates
4.9(103)

No Logo - 0.2mm layer, 2 walls, 15% infill
No Logo - 0.2mm layer, 2 walls, 15% infill
Designer
3.7 h
2 plates
4.8(26)

Open in Bambu Studio
Boost
255
582
149
121
1 k
767
Released

Description

The model from JamesThePrinter is incredible. After giving this to a friend as a gift, they asked if they could get one for their daughter that held more game cartridges. After a bit of tinkering, it seemed that it was possible to double the slots. So, that is what we have here. The same principle as the original just with more slots.

 

Both a Logo and No Logo Profile are available.

 

Assembly

You will need 1 x 608 bearing. These are the ones I used. They push fit perfectly on my P1S.

  1. Push-fit a 608 bearing into the center opening in the base.
  2. Put a dab of glue on the spring and insert the tab end into the opening on the inner base circle.
  3. Insert the top into the base aligning the spindle with the bearing opening in the center.

Buy the original designer a coffee!

Comment & Rating (149)

Please fill in your opinion
(0/5000)

Print Profile
With Logo v2 - 0.2mm layer, 4 walls, 15% infill
This printed great on my A1 and I love the idea of gifting these to my two grandsons. I was only confused as to a mention of glue in the description and where to put the tiny piece that printed.
0
Reply
Do you glue down the small squiggly line piece? it just falls everywhere because it’s not secured and I’ve asked the creator and I still have not received a response as to whether or not it should be glued down. Thank you.
0
Reply
The piece that gets inserted into the hole that looks like a squiggly line which I almost threw away is very hard to insert into the hole and keeps falling out.
0
Reply
Print Profile
No Logo - 0.2mm layer, 2 walls, 15% infill
It spins very well with the ball bearing
0
Reply
Did you glue down the small squiggly line piece? it just falls everywhere because it’s not secured and I’ve asked the creator and I still have not received a response as to whether or not it should be glued down. Thank you.
0
Reply
Print Profile
With Logo v2 - 0.2mm layer, 4 walls, 15% infill
Un diseño genial, incluso imprimiendo un rodamiento funciona perfecto.
1
Reply
Print Profile
With Logo v2 - 0.2mm layer, 4 walls, 15% infill
Perfect 👌
0
Reply
Print Profile
With Logo v2 - 0.2mm layer, 4 walls, 15% infill
Excelente
0
Reply
Print Profile
With Logo v2 - 0.2mm layer, 4 walls, 15% infill
I printed the spring in PETG, since previous experience tells me this is a better material for springs than PLA. I didn't have a bearing, so I printed one of those too. The top and bottom grind a bit against each other, so I wish there was half a mm of clearance between them.
0
Reply
Perfect!
0
Reply
Boosted
Print Profile
With Logo v2 - 0.2mm layer, 4 walls, 15% infill
Super clean print!
0
Reply
Boosted
Print Profile
With Logo v2 - 0.2mm layer, 4 walls, 15% infill
Very easy to put together. Looks nice.
0
Reply
Print Profile
With Logo v2 - 0.2mm layer, 4 walls, 15% infill
Beautiful!
0
Reply

This remix is based on

This source model was used for remixing/sharing before its license was restricted.
Nintendo Switch Game Carousel

License

This user content is licensed under a
Creative Commons Attribution-Share Alike