OTF爪型玩具&OTF Claw cutter toy by phaeozem

phaeozem

Toys & Games>Other Toys & Games

GIF

Print Profile(1)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

OTF爪型刀Claw cutter

Designer

1.4 h

1 plate

4.1(23)

Open in Bambu Studio

Boost

161

314

773

374

Released

Description

这是一个爪型OTF玩具，刀口有尖端，儿童玩耍请注意。

this is a OTF Claw cutter toy,knife edge with tip, children play please pay attention.

提示：请使用4层墙打印弹簧，如果运行不流畅请打磨刀片卡扣

tips:please use 4 wall print spring,If the operation is not smooth, please polish the blade notch

材料＆materials:PETG

分解图&exploded drawing：

更新（2024/1/16）

增加弹簧厚度，使其弹性更大，调整前部可压缩距离，改善刃弹回有几率卡主问题

更新（2024/1/20）

1、缩小内刃比例，使其能适应更大公差。

2、改善限位弹片角度，并对卡扣进行圆角处理，进一步改进运动不畅问题。

3、调整上盖贴合度。

更新（2024/1/27）

1、更新了一个开孔更小的外壳，改善评论区有提到的紧握时会蹭到手的问题。

更新/Update（2024/3/14）

1、调整了弹片角度，改善运行时干涉问题。

2、更新2个配置，分别为：强度、速度。

3、请使用4层墙或100%填充打印弹簧。

1.adjust the Angle of the shrapnel to improve the interference problem during operation.

2.update two configurations, namely: strength and speed.

3.please use 4 layers of wall or 100% filled print spring.

更新/Update（2024/6/19）

1、对运动部件进行圆角处理，改善打印流量问题所造成的运行不畅

2、删除速度配置，统一为“OTF爪型刀Claw cutter”

1.rounding of moving parts，improve movement problems by print flow

2.delete the speed configuration, unified as "OTF Claw cutter"

Comment & Rating (60)

@ChickenBeauty

Print Profile

OTF爪型刀Claw cutter

模型不错，但是阻力太大，不能自动弹出跟收入，可能需要改进。用的petg。

The designer has replied

@phaeozem

打磨一下刀刃边缘，还可以检查一下发条弹簧是否按压到底，与上盖有没有摩擦，内刃间隙留的不是很大，可以根据使用耗材膨胀率，略微缩放内刃大小

@cxsnaile

我也是这样出来有点困难收回去差一点看来是需要打磨

@phaeozem

Replying to @cxsnaile :

感谢你的反馈，可以将刀刃卡扣略微磨圆

@Razieltje

Print Profile

OTF爪型刀Claw cutter

mechanisme doesnt 'jump' open completely. sad. printed in petg. still fun

The designer has replied

@phaeozem

Thank you for liking,you can try to print the blade part at a scale, such as 98%

@user_2734249623

3mf文件在prusa不识别是咋回事？还是只能用拓竹的切片软件？？

The designer has replied

@phaeozem

不清楚，上次拓竹更新好像说3MF改成通用版了，不行你就导出成STL再进prusa切，模型做了无支撑设计，弹簧记得用4层墙或者100%填充打印，弹片推荐使用petg

@james.herring

changed comments to english: This is a claw-shaped OTF toy this is a OTF Claw cutter toy Update(1/16/2024) Slightly increase the thickness of the spring to make it more elastic, adjust the compressible distance at the front, and improve the chance of the main card with the rebound of the blade Update (1/20/2024) 1. Slightly reduce the proportion of the inner edge to accommodate larger tolerances. 2. Improve the angle of the limit shrapnel, and round the buckle to further improve the problem of poor movement. 3. Adjust the fit of the upper cover.

The designer has replied

@phaeozem

my English is poor，thanks for the translation.

@james.herring

Replying to @phaeozem :

No worries, I love this thing. Printed it in ABS with 45% infill. Snapped right together. Took a few seconds to figure out the bottom action trigger, but 10 seconds later - works like a gem, now to do it on the water jet and a heavier spring... Nicely done! 别担心，我喜欢这些东西。采用ABS印刷，填充率为45%。花了几秒钟的时间才找到底部的动作触发器，但 10 秒后 - 像宝石一样工作，现在我需要在水射流和更重的弹簧上完成......干得好！

(Edited)

@phaeozem

Replying to @james.herring :

Thank you for liking it

@Oscar.Baard

Print Profile

OTF爪型刀Claw cutter

fixed it good print

(Edited)

The designer has replied

@phaeozem

Where's the problem？Try polishing it.

@Oscar.Baard

Replying to @phaeozem :

@user_3001277744

Print Profile

OTF爪型刀Claw cutter

could not put it together

The designer has replied

@phaeozem

Look at the GIF above or go to an eye doctor.

@user_3001277744

Replying to @phaeozem :

I did stupid

@user_2155639537

Print Profile

OTF爪型刀Claw cutter

another cool print, I just wish the locking mechanism lasted longer over time. other than that, super cool and a crazy fun thing to fidget with at work

The designer has replied

@phaeozem

Thanks for your comments. It will perform well when using PETG. If it fails, you can make a new one :)