AMS lite Top Mount for A1 alternative version Remixed by aim6mac

Remixed by

aim6mac

3D Printer>3D Printer Accessories

Print Profile(1)

All

0.2mm layer, 2 walls, 15% infill

Designer

6.7 h

1 plate

4.8(20)

Open in Bambu Studio

Boost

120

266

Released

Description

On this Vertical Mount remix u can use the External spool holder provided in the box along side with the ams lite ‘simultaniously’

Tried to come up with an alternative version on the bambu lab ams lite top mount, in this vertical version u can swap the ‘empty’ spools quicker and easier for sure.

it's been tested for 80 hours printtime

enjoy

ams lite

ams lite accessories

Comment & Rating (71)

@gizzmo18

I like the idea but will see how it goes.

The designer has replied

@aim6mac

i'm also using this setup now, i like the way u can change the filament spools quickly with it!

@flynn

hi how tall is it with a reel attached please ,, thanks

@mtodd6040

This worked well for table setup and other printers. The A1 bed moves very far towards the rear. I needed to rotate 90 degrees. The bolt hole is way off so I drilled a new hole and placed a small screw that just barely bites into the AMS

The designer has replied

@aim6mac

hmmm strange, mine lined up perfectly

@aim6mac

thats really strange, somehow i didn't have to line up anything.

@flynn

hi , how tall is this with a spool attached? thanks

@Custer_

Print Profile

0.2mm layer, 2 walls, 15% infill

It works great!

The designer has replied

@aim6mac

looks good!

@flynn

hi , how tall is this with a spool attached? thanks

@Custer_

Replying to @flynn :

It stands 39” tall.

@Djomaster

Print Profile

0.2mm layer, 2 walls, 15% infill

perfect

@flynn

hi , how tall is this with a spool attached? thanks

@TheVirtualJuan

Print Profile

0.2mm layer, 2 walls, 15% infill

Great model. I was worried it would wobble, but there's been no issue! Printed in PETG

@ricky.kollberg

Very nice works perfect a had some trouble lining up hole on the side but opend it up a bit

The designer has replied

@aim6mac

glad it worked out for you, but that could be a sign of having to turn it upside down to align it perfectly.

@user_3788079598

have the same issue, the hole isn't in the correct location sorry

@flynn

hi , how tall is this with a spool attached? thanks

@emcy_uk1

Print Profile

0.2mm layer, 2 walls, 15% infill

Still standing firmly after a week.

The designer has replied

@aim6mac

awesome, mine is going strong aswell :)

@flynn

hi , how tall is this with a spool attached? thanks

@emcy_uk1

Replying to @flynn :

Appr. 57-58 cm from top of the top bar

@KevbotV87

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

So much free space should of done this sooner

@flynn

hi , how tall is this with a spool attached? thanks

@KevbotV87

Boosted

Replying to @flynn :

Oh sorry I just saw this message let me measure it for you when I get home from work

@flynn

hi did you get a chance to measure it thanks

@tbeau311

honestly has been great, I’ve had it for well over a month and I don’t have any worry about balance or anything, hoe was like 1 mm off but some slight dermal did the job lmao

The designer has replied

@aim6mac

glad to hear that, works for me too

@flynn

hi , how tall is this with a spool attached? thanks

@tbeau311

Replying to @flynn :

sorry if I’m too late, from the lowest point of the printer to the top is about 4.5 feet give or take a few inches

@1darkprince

Print Profile

0.2mm layer, 2 walls, 15% infill

sphegetti everywhere