Great test. Thanks for designing and sharing!!

I bought a Ryobi cordless vacuum for my 3D printer room and needed some goodies for it. Your accessories were exactly what I wanted. I used an outer brim just to be sure they didn't topple over. All printed perfect. I then designed a very sturdy, wall-mounted holder for up to 6 vacuum attachments. Thanks for sharing your design with us.

Thank you for the great effort and sharing with us. The fruits of your work will definitely improve my prints. The bottom image is the default settings on my H2D. The top image is with your "best" settings as a starting point. The gray is Bambu Lab PLA and the black is Sunlu PLA with generic filament settings. The improvement in surface finish is quite clear. I'm looking into why the gaps around the hole got worse with your "best" settings; haven't figured it out yet. Any suggestions?

Spectacular design!! Aliens is one of my all-time favorite sci-fi movies. It printed perfect on my H2D. I used a two-tone tan/brown matte filament and added a contoured fuzzy skin to give it a reptilian skin look. It is SOOO creepy... but so cool at the same time. I am printing a 2nd one upscaling to as large as my bedplate can handle. When I get another boost, I'm giving it to you. Thanks much for sharing. Edit... Added Momma & baby picture. I scaled up your model to as big as my H2D bedplate could handle. It is eerily realistic at that size. Shivers....

Perfect for what I needed. I have an end table and wanted a way to hang my close-up glasses that I use only a few times a week. Your design and print worked perfectly. A little double-sided tape and all is installed. Thanks for sharing.

Excellent design and perfect print. My wife wanted the shiny purple to match her other printed products in her craft room. After checking your standard 50mm cable guide, she mentioned the 10mm pass-thru depth allowed the cables & connector to easily slip back completely out of the guide. So, I reduced the pass-through depth and made some different sized holes for smaller and larger diameter cablers. I'm now printing a second set in black for the living room. Thanks for sharing.

I have a 2m macbook cord and it works great. I use it nearly every day and will be traveling with it. Really nice design. Thanks for sharing.

I have a 3m usb-c cord and it works great. I use it many times a week and will be traveling with it. Really nice design. Thanks for sharing.

Cool design. My wife wanted it in shiny colors, so the purple and gold went together nicely. It is a bit tipsy with her Android phone, though.

Very nice design. My wife wanted it in shiny purple. It printed great and is very sturdy. Thanks for sharing the design.

Thank you for all the effort to make this very cool storage system. I had no issues printing it. I will use this often as I will be loading it with printer room supplies and stationary goodies. I love having customized items instead of mass market stuff. After some minor cleanup of drawer outer edges to allow for smoother movement and a number of drawer break-in open-close cycles, I finally decided to drill holes in the back wall near the middle of each drawer. This helps to reduce the pressure build-up when closing drawers. You might consider a built-in 7mm dimeter hole in the back wall of each drawer area. I recommend one hole in the middle of each of the top smaller drawers and 2 holes evenly spaced-out (width-wise) in each of the bottom three full-width drawers.

Thanks for the great and very useful design and print profile. It came out excellent. Greatly appreciated.

I really like your design and wanted to give you high marks (prefer 4.5 so it would indicate room for improvement but went with 5 for now): Positives: - Deep screw adjustment length to fit thick tabletops (like mine) - Large underside contact area because of threaded spacer (great idea!!!) - Large flange on top of table for clamping to hold tight Things to Consider for Improvement - The thread is quite loose. While it works, if you tighten up the thread tolerances, it would feel and secure much better. - The size of the gap to insert the cables doesn't fit the thicker power cables (like for my laptop). I had to hand trim the far right holder location to widen the cable gap so that I could get my laptop power USB-C cable inserted. Maybe consider having one of the gaps to be extra wide in order to support usage of thicker cables.

Very nice design and good improvements. I expect to being using your grease applicator tip for many years.

Excellent kit. Thank you!!!

Great design. It printed well and I will be using it very soon. Thanks much for sharing with all to use.

Thanks for the design and print profile. I scaled it to fit a "First Alert EZ Fire Spray Can" and it works great. It's very stable, strong and keeps the extinguisher easily removable. I have one in my printer room and one on the wall just outside the printer room, just in case. I was using a printed different design (from Makerworld) but was never happy with it because the can could be accidentally knocked off quite easily. Your design is MUCH better. I greatly appreciate you sharing your work with all to use.

Turned out great in PLA Silk Pink. My wife is giving it as a gift along with a few of the coasters and tray. Thanks for the design and print. It all woked perfectly.

Thanks for the very useful cable organizer. It is exactly what we needed. My wife is using the regular sized design while I needed the taller design because the top of my end table is over 35mm thick. Well done!!

Your lightsaber's are absolutely spectacular in their design and printing methodology. Well done!! This is my first and likely not my last that I will print of your designs. Superb. 2 boosts coming your way.