Zixxer10r

paulkaliszuk

Designed and printed leg risers for my thuma bed frame. The legs will raise the bed about 7.5 cm. 4 copies of the legs + 1 center leg and you're good to go.

Thuma Bed Riser

Furniture Risers

DKdevt

A fun toy gun that launches discs with a magazine for 15 discs of 20mm.It shoots with great speed and accuracy at short distances.&nbsp;<ul><li>Completely printable design. </li><li>No need for extra screws or glue. </li><li>Just 2 elastic bands for the push mechanism of the magazine and the trigger striker.</li><li>Use a pair of fine-tipped pliers to help you with the assembly of the rubber bands. </li><li>Skills are required for assembling the mini gun. </li><li>The design consists of multiple parts with very tight tolerances. </li><li>Use PTFE(Teflon) grease for perfect operation and increase performance.</li><li>Please perform a filament flow calibration! </li><li>Use previously dehydrated and high-quality filaments.</li></ul>&nbsp;Check the new Power pack to increase shooting distance and accuracy with reinforced toroidal bullets:https://makerworld.com/en/models/486278#profileId-398995You can print extra magazines and easily reload your disc launcher. Enjoy :P&nbsp;Consider supporting my work with a &#34;Boost&#34;🚀 and a &#34;Like&#34;👍🏻 so I can continue creating refined designs to share for free with everyone.🤓

Disc Launcher Semi Auto Rapid Fire Print-in-Place 

Guns

ben.hallauer

LoveSac makes a really good cupholder for their couches, but it has trouble with mugs because of the handles.Designed this to remedy that problem.&nbsp;Things to note:<ul><li>it fits the couch sides/backs more tightly than the one from the retail store.</li><li>it is designed to fit normal and larger size mugs, so if you have a small tapered mug, this might be too big.</li></ul>&nbsp;Printing notes:<ul><li>Print this in side or upside down orientation, but you will need supports.</li><li>Highly recommend 4-5 levels for the top most surface layer.</li><li>Legs should run, at minimum, 20% infill to prevent too much flexing when placing on the couch.</li></ul>

LoveSac Sactional All-Purpose Mug Holder

Lovesac

fay3dlab

This is my entry to the flying object competition.. So i have been brainstorming of a design i can make for the competition and i knew i will make a suspended model for it.. But to make it different than my usual suspended model i need to add another element.. that's where the tensegrity comes in.. Tensegrity is basically a model that is floating solely by the tension integrity from the weight of the model itself.. in other words.. the X-wing will look like its floating and only supported by the suspended strings.. Like all my suspended model.. it will be printed in one piece except for the 4 back thruster engine.. that needs to be installed after print.. Once printed.. you need to be very careful when getting it off the bedplate since unlike other suspended model.. this one is held by very little strings.. the wings are held by 10 strings in total..&nbsp;I have also prep the model so that you can easily paint parts for multicolor prints.. <img src="https://makerworld.bblmw.com/makerworld/draft/378390/2023-12-02_24f73bb26f471.png"> I've made the model small in size cause of the weight of the x-wing that the strings will have to bear.. and so that our A1 mini owners can join in the fun of printing this suspended tensegrity modelOne important thing to remember is to set the wall generator to arachne from classic.. this will make the slicer print the strings..I hope you guys have fun printing this suspended tie adv fighter

Suspended Tensegrity X-Wing

Star Wars Replicas

Techro3D

Classic bird feeder | octagonal house | with mounting bracket| By Techro3D&nbsp;<ul><li>Water drainage.</li><li>Mounting bracket.</li><li>Suspension point for a fatball or other bird food.</li><li>Bottom also suitable for placing food.</li><li>Removable roof.</li><li>100% printable.</li><li>No glue required, but can be used just to be sure.</li></ul><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000453035/design/2024-05-04_a142276d19e56.png"><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000453035/design/2024-05-04_bf6862079a949.png"></figure>

Classic bird feeder, octagonal house.

Bird Houses

Bo Andersen

holder for le creuset and others in 63,3mm size

le creuset salt & pepper

Pepper Mill Stand

PRINT_ON_DEMAND

Licence commerciale disponible sur patreon : https://www.patreon.com/PrintOnDemand Le Pyroserpent est une variation rare et mystérieux de la célèbre espèce de Pokémon dragon-feu. Contrairement à ses cousins plus communs, le Pyroserpent présente des caractéristiques serpentines distinctes qui le rendent unique. Son corps est plus allongé et sinueux, avec des écailles brillantes qui reflètent la lumière d'une manière hypnotique.&nbsp;<figure class="image image_resized" style="width:100%;"><img src="https://makerworld.bblmw.com/makerworld/draft/462577/2024-01-28_b51dd90685c53.png"></figure>

dracaufeu serpent pokemon PyroSerpent

Lizards

user_1257945679

This model came from Nexopixls Compatible model. I removed a coupler on the original emitter to make it fit better to shorter saber lengths, and allow for better lighting of the saber. I have added paint and colors to see what I did. The print took 2.5 days and 1500 filament changes, but came out flawlessly.&nbsp;The holes on the Emitter 2 were a little small, so used a tool to enlarge them, and once completed fit perfectly and was able to glue it in place. The hilt, pommel, and grip is extremely heavy duty, and can take a beating. The saber portion is only for show.

Cal Kestis' Fallen Order Lightsaber

Lightsabers

LoboCNC

<figure class="media"><div data-oembed-url="https://youtu.be/3CzV9iwZRQc"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/3CzV9iwZRQc" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>With this 21 shot rubber band shooter, you'll be able to rain hellfire (hell rubber?) down on your competition. This is a completely redesigned version of my <a target="_blank" href="https://makerworld.com/en/models/95135" rel="nofollow noopener">earlier rubber band shooter</a> with a vastly simpler trigger and indexing mechanism, and more stretch for longer shots.&nbsp;The mechanism uses a pawl and ratchet for turning a worm gear that both advances the magazine and releases each band. Pulling the trigger causes the worm ¼ turn, advancing the magazine by one tooth. The leading edge of each of the 4 threads on the worm is what pushes each rubber band off of the nub above each tooth gap.&nbsp;Assembly<ol><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_487e03e1072d6.jpg"> Remove the small built-in support that sits in the trigger slot.  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_affbef958b134.jpg"> Insert the trigger into the slot  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_3180e31dfd26.jpg"> Slide the U-shaped clip over into the notches in the trigger to hold it in place.  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_a5eb3274b4a56.jpg"> <img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_baca0d09c4d03.jpg"> Slide the pawl into the slot at the back of the shooter and place the hole in the end of the pawl onto the post on the trigger.  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_8fad8a27fedeb.jpg"> Screw the worm onto the back end ot the shooter with one of the screws.  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_a5a8995ebfeae.jpg"> Hook a small rubber band between the hook on the trigger and the hook on the frame.  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_5bed8080ce354.jpg"> Screw the tip of the magazine into the front end of the shooter with the second screw.  </li></ol>Play You are now ready to load the rubber bands. The stretched length of the bands is about 280 mm and you can use any 1.5-3mm wide bands that will stretch that far.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_dbb06ff5acfb8.jpg"> <img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_64708c74cef49.jpg"> <img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_722e3012b36f9.jpg"> Start at the right side of the magazine. Loop one end of the band over the nose of the magazine and then hook the other end over the little nub above the gear-tooth gap. The 3rd photo shows how it looks as you progress.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_07e79f6f6406b.jpg"> Now pivot the magazine around so that the left-most tooth engages the worm. Each pull of the trigger should advance the magazine one tooth and release one rubber band.

21-Shot Rubber Band Shooter

Rubberband Guns

Darrare

A prop/cosplay sword and sheath that holds a standard dice set for D&D. I printed a bunch of these out for friends for Christmas or birthday gifts super easily, only very minor supports needed.&nbsp;The hilt and blade have some nubs that interlock, but what I did was I used the hot end of my hot glue gun to melt the nubs and melt a bit in the hilt to create an uneven surface to let the hot glue really hold with a strong bond. I also just tried plain super glue and it held really well, but not as sturdy as the hot glue gun method.

Dice Holder for D&D Dice Set

dadhacks

This is a different take on the standard purge (poop) chute and bucket. Let your little ghosts slide or drop into the ghost trap, with handle for easy removal and dumping. 2 options available - 1 with the containment unit for those that put their ghost trap behind the printer, and 1 with a slide for those that want their ghost trap on the side.&nbsp;Notes:<ul><li>Ghost trap is meant to be assembled with glue. This was done to keep purge and print time to a minimum. Flat design meant to accommodate tight placement against printer.</li><li>This has been broken out into 5 different build plates to limit each to 4 colors per plate for those with only 1 AMS.</li><li>Smooth PEI recommended for the side panels and doors; just gives a nicer finish.</li><li>Need to use 2 15x3 magnets for the slide.</li><li>Need to use one of the longer M3 course threaded screws (or similar) from the scraper kit that came with the printer to hang the containment unit chute.</li><li>Supports required for containment unit chute and part of the handle.</li><li>Vent holes in side of containment unit chute to keep from impeding any airflow to the vents on back of printer.</li><li>Please note the build plates are preselected. If you want to use a different build plate, please ensure you click the nut icon next to the build plate to change. </li></ul>

Ghost Trap Poop Chute Kit for BambuLab P1 and X1 Series 

Poop Chutes

TrendtB

Make your kitchen herb gardening easy - ideal for busy cooks and gardening enthusiasts, this planter ensures your herbs stay hydrated and fresh, even on your busiest days. If you're an avid cook, or know someone that is - start printing now and add a touch of green to those kitchen counters!&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/323633/2023-12-29_27004b97fd569.gif"><figcaption>Make various patterns and arrangements with multiple planters</figcaption></figure>&nbsp;Inspired by my wife's passion for cooking with fresh herbs, this planter is designed to blend seamlessly into any kitchen aesthetic. Perfect for those who appreciate both functionality and style in their cooking space.&nbsp;<h3>KEY FEATURES</h3><ul><li>Easy Self-Watering: Built-in reservoir keeps herbs hydrated.</li><li>Artistic Design: Intricate floral pattern forming a love heart, adding a decorative touch.</li><li>Dual-Purpose Base: Use a standalone base as a stylish container for herb gardening tools.</li><li>Batch Printing Profiles: Optimized for quick and efficient batch printing.</li></ul>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/323633/2023-12-29_0b77f080a19a4.gif"><figcaption>The floral design allows you to play with different patterns depending on how the planter is placed.</figcaption></figure>&nbsp;&nbsp;<h3>HOW IT WORKS</h3>The planter is designed to slowly absorb water from the reservoir (base), which you occasionally top up with water. There is a seam that acts as a guide for how far to fill. Don't fill over this line or water will be pushed out through the top!<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/323633/2023-12-29_f7d43224f4262.gif"><figcaption>The base acts as a reservoir of water - fill to just below the seam then place your plant on top</figcaption></figure>&nbsp;When you're planting your herb in the top half, it is recommended to use a wicking material at the very bottom. This helps to slowly absorb water into the soil and roots. You can place a couple of cotton balls / cotton wool in the bottom of the pot to do this. Then fill with soil, and your herb of choice.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/323633/2023-12-29_d13556ba7b91.gif"><figcaption>Place cotton wool into the bottom of the pot to act as a wicking material.</figcaption></figure>&nbsp;&nbsp;<h3>PRINT SETTINGS</h3>Use the designer profiles to ensure the base is water-tight, or you'll risk water seeping through the print! If you're looking to adjust the profile, or build your own - these are the key settings to maintain ensure there are no leaks:<ul><li>Infill overlap: 50%</li><li>Walls: 3</li><li>Top shell layers: 5</li></ul>Additional profiles have been provided to batch print, or print using a single plate and color.

Self-watering Herb Planter for the kitchen

Kitchen

letitbe.7

Remix of Articulated Toothless from How To Train Your Dragon created orginally by <a target="_blank" href="https://www.thingiverse.com/Turaak" rel="nofollow noopener">Turaak</a> from thingiverse(thing:6011165).Ready to print with AMS with two colors (black and green).Enjoy!

Articulated Toothless from How To Train Your Dragon

Dragons

chippwalters

Use my print profile for best results, I cannot guarantee print profiles by others.<h3>Here is a nifty snap together stacking set of pill boxes (50mm x 50mm x 24mm). Each box has an engraved letter(s) of the day.</h3>The lid has a tiny logo, but there is also a lid without the logo as well. There is also a plain box with no days of the week engraved. They have all been printed using Bambu Lab Matte PLA as well as generic PLA and they works fine. Also, printed and tested on X1C, A1 and A1 mini.&nbsp;If the snap is too tight, try snapping/unsnapping a few times and it will loosen. If still too tight, just use a nail file on the snap nubs to lower the resistance.&nbsp;This is a Single Color profile for X1C.There are a number of other print profiles, including multi-color for A1, A1 mini and X1C. The color profiles only have 3 filament swaps for the entire print. Those profiles are set to print each box with the correct filament color, then go on to the next. Because of the print sequence by object, you'll need to print out 2 plates, on for Su,M,T,W and another for Th,F,Sa,Lid.&nbsp;Let me know if there are any other sizes/designs that you would like.

Stackable Snap Together Pill Boxes

Medicine

Joshua.loebenberg2

Designed this for a colleague upon a request for his office space. I figured I put the work in, might as well throw it on Maker World for anyone else to enjoy. Can add/print additional hooks for double sabers and such.