Editing my review after creator made som tweeks to the design. Now it's good and a AWESOME adition to the Catan settup. Really nive to remove the cardboard circles with printed numbers and use these instead. I have swaped the polarity to be oposite in the 4player set vs the 6player set. This way they do not stack together the same direction and are easy to seperate. I have printed the 6x2mm sett and it works really well, but if you have the magnets or are buying magnets for this project I think I recommend the new 8x2mm magnet version for some added strength. I also had opposit polarity in the holder to make them stack with the letter side up and number down. If you put a 6player pice in the slot for the 4player set it will not go inn with the letter side up and you will see it is in the wrong slott. All in all if you play Catan just print this easy and nive uppgrade.

Glued these to a few christmas presents. A unique way to decorate gifts that most people have not seen before. It was a hit and christmas. Might print again.

used these as nametags on christmasgifts and they where a hit. I strongly belive I will print loads of these next years christmas.

Looks good and with the basket (long) it fits ALLOT of filament before you have to empty it. Attaches nicely with the magnets. I reccomend printing in ASA to avoid hot PLA to stick to it. I printet mine in ASA and it printed with zero problems and looks and works fantastic.

These amazing and a must have for Heroes of Barcadia. I have printed like 70 of these frames and need tl finish putting in magnets. I been talking quite a bit about the design with the designer and he is also super nice to talk to and after we discused spacing the magnets out more and then adding a third hole they are allot better. I highly reccomend to only print the 3 magnet version to have the most flexibility. You can start with one magnet in the center hole and then if you find it to be to weak you can just add another one in either the left or right hole on all of them or go all out and go for all three. No need to reprint. If you start with the two magnet version like I'm going to do for all the black tiles (the brown center tiles will get 3 magnets right of the bat.) then use the left and right hole leaving middle hole empty. Nice to be able to uppgrade later without printing again if you need more strength and 3 magnets.

I really enjoy this one. Looks super nice on my outside table. Printed really nicely in PLA. Nose and eyes was a bit hard to fitt, but some sanding and it was good. All in all a cute and really nice model. I like it

These print fast, super easy and work AMAZING. The most annoying part of Carcassone is when you reach the end of the table because everyone build in one direction and you need to move the whole board and the tiles moves in all directions and you must remeber how the board was settup again after moving every tile almost one by one. This easy print make that problem history. Just place your palms on top and move the whole thing in one motion. Also it comes out of the printer ready to go. No post print work like gluing or anything, it just works. ALWAYS wait for the build plate to cool completely before removing them and try to not bend it to much during removal from build plate. I removed one from a hot plate and it warped and was not good to use. 2 days under heavy books made it usable again, but not as good as the ones removed when buildplate was cold. AWESOME PRINT. check out my holder that holds 30 frames securely: https://makerworld.com/models/2307743?appSharePlatform=copy

Printed just fine in PLA and works as intended.

my first day owning a printer and these prints greate. I have printed Loads of these and there is only a few complaints. at some of them the pressfitt is way to hard, but that might be my printers fault. Also the part pushing out the magnets should be longer because there is always 3-6 magnets that you're not able to push out because the slider stops and is not long enough to reach the end of the pipe. Still these are AWESOME and if you work with magnets you have to print them.