PflanzPfoten

MakerVerse Designs

A Gardena to ¾ inch thread adapter<ul><li>the Adapter is printed in PLA or PETG</li><li>the Sealings are printed in TPU</li></ul>Have fun with it and leave a like or subscribe if you like it!If there are any suggestions for improvement, feel free to write a comment.

Gardena Adapter - to 3/4 inch thread

Alltagshelfer

ST3V3DDRUCK

Power Outlet Cover / Light Switch Set to fit the looking of Busch-Jaeger Balance SI future linear&nbsp;The ones shown in the pictures were printed upside down, i recommend printing them on the side to get better curves without seeing the layers that much. Support removal can be quite tricky.

Busch-Jaeger Steckdosen Set

Nützliche Alltagshelfer

oida master

This ptfe color switch is for guys they dont have ams.&nbsp;You can but this mount on the wall and simply change colors without having to go behind the printer to change the filament

ptfe color switch no ams

3D-Drucker Modding

MSearider

Original decora style 2 gang switch plate. Printed in two colors face down on build plate. No support needed.Four 6-32 coutersunk screws need to attach switch plate to switches.

2 Gang Decora style switch plate stars

Was man mal drucken kann

Codyinbody3

Here&#39;s another Hueforge I enjoyed designing. I took a little while with this one making it a little thicker than normal and also making the colors have more depth. Feel free to change it up as you see fit. If you have adhesion problems, be sure to put on a brim that&#39;s close to the object. Enjoy!&nbsp;This is the first model I included the STL raw file with the model for people that dont have a Bambu Printer (Done by request)&nbsp;Swap Instructions:     Start with Black     At layer #6 (0.56mm) swap to Red     At layer #16 (1.36mm) swap to Yellow     At layer #27 (2.24mm) swap to White for the rest.

Pikachu v1 Huefroge

Druckbilder

SASSy Design

A simple but playful design inspired by the small patterns of paws pressed on fresh concrete.&nbsp;Print information:<ul><li>Recommended vase mode or semi-vasemode settings (0% infill, 0 top layers, 4 or 5 bottom layers, 2 or 3 outer perimeters - for a stronger print)</li><li>Recommended using a lower layer hight (0.15/0.2mm) for better results in details</li><li>Prints very good in any filament</li><li>The model is scalable to your liking</li></ul>Happy printing!

Animal Paw Plant pot Planter - Vase mode design

Pflanzenzubehör 

angry-p1p

Have fun with this Nintendo Switch Dock Cover. This cover is for the “normal” Switch Dock, I don't know if the OLED-Dock is different.&nbsp;If your printer and filament is dialed in it should slide right over your dock.&nbsp;To ensure you waste as little filament and time as possible I added a small test piece on a second plate. If needed adjust/scale it by a tiny amount according to your tolerances or filament.&nbsp;All my prints use Sunlu PLA +. A first layer and first layer infill speed of 25mm/s, only one wall on first layer and a first layer line width of 0.25mm at a nozzle size of 0.2mm.&nbsp;See my other designs:&nbsp;0.4mm Nozzle<figure class="image"><a href="https://makerworld.com/en/models/142964" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/413037/2024-01-15_fcdb734775fbb.jpg"></a></figure>&nbsp;0.2mm Nozzle<figure class="image"><a href="https://makerworld.com/en/models/142951" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/413037/2024-01-15_14ad28212c045.jpg"></a></figure>

Alltagshelfer

Nützliche Alltagshelfer

3D-Drucker Modding

Was man mal drucken kann

Druckbilder

Pflanzenzubehör

Switch Zubehör