richard.bernards

zwurtz182

Designed some key caps for this macro keypad I bought online. Should fit any standard switch but is rather low profile.&nbsp;Best printed either face down or with supports face up.

Macro Keypad Key Caps

macropad

Danrusso

Sculpture of a Girl Face modeled with green leaves.Fantastic piece of Decoration for your home inspired to our Green Planet

Dreaming Nature

Showcase

Josh-3D

A Travel 9x9 Go board complete with pieces! Conveniently folds up to hold everything tidy while on the go!&nbsp;The second of the two 9x9 travel go games. This one uses a styling I'm calling “scifi styling” Not sure how scifi it turned out, haha, but it's still pretty neat. I nearly completed the first one when I got the idea for this. I couldn't leave well enough alone though so had to give it a go, and thus, this was born! &nbsp;Print the sides, mid section, and the cases. Print a set of the player pieces in each color. There should be 40 player pieces total. On the X1/P1, I recommend printing without the Aux fan to help avoid warping. Make sure your bed is clean too! &nbsp;You'll need 4 M3x20 (there abouts, doesn't have to be exact) screws for the hinge, and 4 4x6mm magnets (<a target="_blank" href="https://www.amazon.com/gp/product/B075PMYRFT" rel="nofollow noopener">Here's a link to an Amazon US listing</a>). Be careful not to over-tighten the screws! You don't want a stiff hinge.&nbsp;

Go 9x9 Travel Board w/pieces - Scifi Styling

Games

weeeak

Higher version of <a target="_blank" href="https://www.printables.com/@DieserJonas" rel="nofollow noopener">@DieserJonas</a>' CR2032 Gridfinity bin. Wanted it to be the same height as the “no lip” models of <a target="_blank" href="https://www.printables.com/@Dalkain" rel="nofollow noopener">@Dalkain</a>'s <a target="_blank" href="https://www.printables.com/model/341811-gridfinity-battery-trays-aa-aaa-aaaa-18650-cr123-c/files" rel="nofollow noopener">Gridfinity Battery Trays</a>. Orignal Description:A small 1x1 Gridfinity bin that holds 8x CR2032 batteries. Created to be as simple as possible, without a stacking lip and without magnet and screw holes.<h4>Print Instructions</h4><ul><li>Any basic PLA should work</li><li>0.2 mm layer height</li><li>0.4 mm nozzle</li><li>PrusaSlicer speed profile</li></ul>

Gridfinity bin for CR2032 batteries

Gridfinity

Brian Dean

<h2>Embedded Magnet Dispenser Tool for Multiple Diameters and Thicknesses</h2><h3>PROFILE NOTE</h3>Please use the “Designer” profile as it guarantees the latest files and version with all new magnet sizes and features. The Designer Profile will be listed at the top.<h3>Latest Update (2024-04-21): Quick summary</h3><ol><li>additional magnet sizes</li><li>magnet size text embossed on the barrel and also included on the slider</li></ol>See below for the more detailed update notes.<h2>Magnet Dispenser for 3D Prints: Simplify Magnet Insertion with Precision</h2>The Magnet Dispenser Tool is expertly designed to streamline the insertion of magnets into 3D prints. This tool not only speeds the process of inserting magnets into 3D Prints, it also ensures correct orientation and secure fitting, making it ideal for projects that require precise magnet placement.<h3>Key Features</h3><h4>Dual Dispensers for Perfect Alignment</h4><ul><li>Includes two dispensers for each magnet size – one for north-up and one for south-up orientations</li><li>Use different colors (e.g., red for north-up and blue for south-up) to help easily identify the dispenser&#39;s orientation</li><li>Eliminates the hassle of misaligned magnets</li></ul><h4>Design and Utility</h4><ul><li>Developed after extensive refinement</li><li>Allows for friction-fit insertion and is also suitable for magnets that are glued</li><li>Tapered tip facilitates use in tight spaces</li></ul><h4>Ease of Use</h4><ul><li>The dispensers are designed to accommodate the specified magnet sizes for their internal holding magnets, but can dispense magnets of any thicknesses for the specified diameter. For example, for the 6x3mm dispenser, you will need 6x3mm magnets to assemble the dispenser, but once assembled, that dispenser can dispense any 6mm diameter magnet such as 6x1, 6x2, 6x3, 6x5, etc.</li></ul><h4>Convenience and Storage</h4><ul><li>Features a snap-on cap with an embedded magnet and a top slider magnet</li><li>Ensures secure storage and prevents accidental magnet spillage</li></ul><h4>Customization and Printability</h4><ul><li>No supports needed for printing</li><li>STL and STEP files included for personal customization</li><li>Compatible with PETG, PLA, ASA, ABS, etc</li><li>Adjust x/y hole compensation if needed for perfect fit</li></ul><h4>Visual Guide</h4><ul><li>Fusion 360 images provided for easy assembly and understanding of the internal mechanism</li></ul><h4>Use the Magnet Dispenser for a hassle-free, precise, and efficient magnet insertion experience in your 3D printing projects.</h4><h3>Supported Magnet Sizes</h3><h4>Dispensers are now provided for the following magnet sizes as of Version 5</h4><ol><li>2x1mm</li><li>2x2mm</li><li>2x3mm</li><li>3x1mm</li><li>3x2mm</li><li>3x3mm</li><li>4x1mm</li><li>4x2mm</li><li>4x3mm</li><li>5x1mm</li><li>5x2mm</li><li>5x3mm</li><li>6x2mm</li><li>6x3mm</li><li>7x2mm</li><li>7x3mm</li><li>8x2mm</li><li>8x3mm</li><li>8x4mm</li><li>9x2mm</li><li>9x3mm</li><li>10x1mm</li><li>10x2mm</li><li>10x3mm</li><li>12x2mm</li><li>12x3mm</li><li>15x2mm</li><li>15x3mm</li><li>20x2mm</li><li>20x3mm</li></ol>NOTE 1: The 1mm magnet thickesses are just too thin to work reliably with the friction-fit of the slider and caps. Therefore, I have made the pockets of the “1mm” thickness magnet dispensers to be that of the 3mm variety so that they work. So to assemble a 1mm magnet thickness dispenser, you will need to purchase a few 3mm thick magnets to assemble the dispenser. A 2mm thickness will likely work ok, too. Note that the text on the dispenser will still say “D x 1 mm” for the barrel, “Dx1” on the cap, and “D/1” on the slider, so you know what magnets you have loaded into it.&nbsp;NOTE 2: the above are the sizes needed to assemble the dispenser. The dispenser can still dispense any thickness of magnet as long as the diameter is the same. So if don&#39;t see your specific magnet thickness listed above, you can still print the correct diameter, assemble the dispenser with the correct magnet thickness, and dispense other thicknesses.&nbsp;STEP and STL raw files are included if you do not wish to use the provided profile.<h3>Quality Assurance Testing</h3><ul><li>All dispenser sizes have been printed by me and extensively tested</li><li>I have purchased all magnet sizes at significant expense to myself to ensure fit</li><li>Magnet diameters are tricky for press-fit tolerance and controlled by no less that 5 Fusion 360 parameters that must be balanced to achieve good fit<ul><li>Multiple iterations of each dispenser were printed and refined</li><li>Many kilograms of filament and hundreds of hours of print-time were consumed during this process</li><li>All to ensure the best quality printing and fit-up for each dispenser size</li></ul></li></ul><h3>About the Profiles</h3><ol><li>Please use the “Designer” profile as it guarantees the latest files and version with all new magnet sizes and features. The Designer Profile will be listed at the top.</li><li>NOTE: The “Designer” profile is a single profile that contains plates for all magnet sizes so far. Please ignore the “total time” reported by MakerWorld for the profile. You only need to print the plate(s) that you need. Each plate takes about 2.5-2.9 hours on my X1C using the included “PETG” profile which is slowed down for good PETG layer adhesion and quality.</li><li>While the other profiles may be ok, their file / update version may be out of date. So if you want the latest sizes and model improvements, please choose the top “Designer” profile.</li></ol><h3>Accessories</h3>Be sure and check out some nice accessories that other folks have created to work with these dispensers.<ul><li>Tip Caps - these are nice caps for the dispensor tip. Not only do they help keep the magnets contained within, but they also protect the tip. Additionally, they are labeled with the magnet size, which is nice. Thank you @onegotowned ! <a target="_blank" href="https://makerworld.com/en/models/149038#profileId-162633" rel="nofollow noopener">https://makerworld.com/en/models/149038#profileId-162633</a></li><li>Vertical Workbench Stand - This is a very nice stand for select diamagers made by @nickramsey57. A number of folks have asked about stands / organizers for the dispensers, so this model will likely be useful to a number of folks. Thank you @nickramsey57 ! <a target="_blank" href="https://makerworld.com/en/models/206388#profileId-226561" rel="nofollow noopener">https://makerworld.com/en/models/206388#profileId-226561</a></li><li>Vertical Workbench Stand (parametric) - Here is another very nice stand made by @RevHazlett. You can specify the dispenser sizes that you want it to hold and then generate, making it customizable to your needs and the common magnet sizes that you use. Thank you @RevHazlett! <a target="_blank" href="https://makerworld.com/en/models/435087#profileId-340031" rel="nofollow noopener">https://makerworld.com/en/models/435087#profileId-340031</a></li></ul><h2>Update History</h2><h3>Version 5: 2024-04-21</h3><ol><li>Emboss the magnet size text on the Barrel (see photos), allowing one to view the size from the side, and also allowing one to print all of the barrels on a single plate and not get the barrels mixed up as to what size they are for.</li><li>Include the magnet size text on the Slider (see photos), allowing one to print all of the sliders and caps together on one plate and not get the sliders mixed up as to what magnet size they are for. Also provides additional text identification of the magnet size within.</li><li>Include 11 new magnet sizes:<ol><li>3x1mm</li><li>4x1mm</li><li>5x1mm</li><li>7x2mm, 7x3mm</li><li>8x4mm</li><li>10x1mm</li><li>15x2mm, 15x3mm</li><li>20x2mm, 20x3mm</li></ol></li><li>Re-organize the plates so that they are a little easier to manage. All dispenser sizes for each “diameter” are spread across three plates now - the Barrels, the Red Caps and Sliders, and the Blue Caps and Sliders. This allows one to “print-by-layer” instead of “print-by-object”, and the text also comes out better. Additionally, it is now easier to construct a plate with all of the size variations on 3 individual plates and print them all at once.</li></ol><h3>Version 4: 2023-12-26</h3><ol><li>Fixed an issue where the smaller diameter magnets such as the 2mm, 3mm, and possibly the 4mm magnet diameters could inadvertently slip through the vertical barrel slider stem slot. Prior to this update, the slider stem was a fixed 3mm + tolerance width. With Version 4, the slider slot is now dynamic based on the magnet diameter. So now, the smaller diameter magnets are captive within the barrel and cannot slip out inadvertently.</li><li>Tighten up the tolerances between the “slider” and the “barrel” for a better fit and smoother operation.</li><li>Use the Profile: “Version 4: All Sizes …” for the latest from this update.</li></ol><h3>Version 3: 2023-12-22</h3><ol><li>Added additional magnet sizes<ol><li>2x1mm, 2x2mm, 2x3mm</li><li>9x2mm, 9x3mm</li></ol></li><li>Text is now added within the Fusion 360 Model File, eliminating the need to add the text using Bambu Studio<ol><li>Ensures consistent text placement and easier colorizing of the text</li></ol></li><li>All plates are included for all magnet sizes, two dispensers per plate, print sequence: print-by-object</li></ol><h3>Version 2.1: 2023-11-28</h3><ol><li>Added additional magnet sizes<ol><li>3x2mm</li><li>4x2mm, 4x3mm</li><li>5x2mm, 5x3mm</li><li>6x2mm</li><li>8x2mm, 8x3mm</li><li>10x2mm, 10x3mm</li><li>12x2mm</li></ol></li><li>The magnet size text is included on the cap for easy identification - see photo</li></ol><h3>Version 2: 2023-11-20</h3>Updated to “Version 2”. Significant updates an enhancements have been made, some seen, some unseen.<ol><li>Added additional magnet sizes<ol><li>3x3mm</li><li>12x3mm</li></ol></li><li>Each magnet size is on its own plate, two dispensers per plate, print sequence: print-by-object</li><li>Redesigned “thumb slider” for greater comfort and stronger press force</li><li>Slider stem has been reinforced</li><li>Many enhancements for smoother operation with internal chamfers and fillets, enhanced tolerances, and strengthening of key internal components</li></ol>&nbsp;&nbsp;&nbsp;

Embedded Magnet Dispenser Tool for 3D Prints

Tools

Joker 3D

Started to print all the Super Mario Brothers Character & really liked this STAR model BUT needed it with 2 colors (Yellow&black for the eyes) - so made a remix. Thanks @ReProps from printables for great model!&nbsp;Added a Stand for it. Print in 3 Colors: Yellow for the Body, Black for the eyes & Gold for the stand. Enjoy!

Super Star [SUPER MARIO]

Kids

SWAT8989

<div><h1>Summary</h1><div>Game : Doom 4 Figur : Doom Marine High : N/A Source : Exported from the game and polished</div><h1>Print Settings</h1>Printer: <div>Tronxy X5S</div> <pre><code> Rafts: <div>No</div></code></pre> Supports: <div>Yes</div> <pre><code> Resolution: <div>0,16</div></code></pre> Infill: <div>10%</div></div>

Doom Marine (Doom 4)

Figurines

Pulsar Designs

This compact, light, and quick-to-print watch holder makes the perfect display for your watch when it's not on your wrist. Its functional and minimalistic design makes it fit in anywhere and with any watch. Even better, this watch holder only weighs about 16g - great for an entire watch collection or as a gift!&nbsp;You can find both the original and mirrored version in the print profile or the raw model files.&nbsp;A matching Base to hold two, four, six, or eight Watch Stands can be found in my uploads or with the following link: https://makerworld.com/en/models/125267#profileId-135291&nbsp;Enjoy!

Watch Stand/Display

Study

Protoprints

An interpretation of Starry Night by Van Gogh made for filament painting.I tried hueforging an image of the original oil on canvas as well, but the outcome didnt look as good due to the nature of the brushstrokes.&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used: Generic Black, Blue, Light Blue, Orange, Yellow, White PLA+ filaments.&nbsp;Swap Instructions: Start with Black At layer #3 (0.32mm) swap to Blue At layer #8 (0.72mm) swap to Light Blue At layer #13 (1.12mm) swap to Orange At layer #19 (1.6mm) swap to Yellow At layer #31 (2.56mm) swap to White for the rest. Two print profiles have been provided as 6 colors are used:<ol><li>for use with 2 or more AMS units</li><li>for use with a single AMS unit</li></ol>&nbsp;The only difference is that the single AMS profile has been set to swap back to slots 1 and slot 2 after printing from slot 4. A pause has been added before the end of the 4th color (orange) to allow for slots 1 and 2 to be changed from Black and Blue to Yellow and White respectively.In summary the print order will be Slot 1 → Slot 2 → Slot 3 → Slot 4 → Slot 1 → Slot 2.&nbsp;UPDATE: An updated experimental print profile has been uploaded with less orange and yellow. Try only if your orange/yellow filaments have a high opacity, causing the picture to look too warm.&nbsp;Protip: Reducing nozzle temps slightly (5 - 10 degrees C) may help prevent stringing on detailed prints like this that require lots of retractions.&nbsp;Happy printing! Share your makes!&nbsp;Note: Bambu Studio shows Error 920 : Non-manifold edges when slicing. This is normal for Hueforge prints. Please ignore and print away :)

Interpretation of Starry Night by Van Gogh - Hueforge - Filament Painting

ThreeD-Michael

Elegant and sturdy drawer box with snap closure for Skat and similar playing cards. There are 2 variants of this box - with and without imprint.<figure class="media"><div data-oembed-url="https://youtu.be/ghlNWSdRNog"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/ghlNWSdRNog" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>Please print in the specified orientation, with a layer height of 0.2 mm and a line width of 0.4 mm or more. Do not use a different layer height as the snap closure is specifically designed for the mentioned layer height.I made the snap closure extra strong to prevent accidental opening - for example in a travel bag. If it is too strong, you can smooth out the snap spots in the frame with a nail file (see last picture above).If you have thicker fingers (like me), you automatically push the frame apart a little in the middle when you pull the drawer, which makes opening the snap lock much easier.

Skat Playing Card Box - Elegant and Sturdy

An ultra slim monitor led light bar. It uses 3mm cob ledstrips and a touch sensor to control the brightness.&nbsp;Additional parts used:<ul><li>DC12v 24V 6A Dimmable Sensor Switch (I got the big spring version)<ul><li><a target="_blank" href="https://nl.aliexpress.com/item/1005003077003427.html" rel="nofollow noopener">https://nl.aliexpress.com/item/1005003077003427.html</a></li></ul></li><li>40cm of 3mm cob led strip (cut into two 20cm lengths)<ul><li><a target="_blank" href="https://nl.aliexpress.com/item/1005004909612656.html" rel="nofollow noopener">https://nl.aliexpress.com/item/1005004909612656.html</a></li></ul></li><li>DC 5.5mm connector<ul><li><a target="_blank" href="https://nl.aliexpress.com/item/1005003324016159.html" rel="nofollow noopener">https://nl.aliexpress.com/item/1005003324016159.html</a></li></ul></li><li>4 M3.5x16 tapped screws</li><li>Some wire to connect everything</li></ul>Note; no affiliate links here, just what I bought.&nbsp;How to print:Please check the photos for the one with the buildplate. You can see only “lightbar-part1.stl” needs a bit of support. The rest is designed to be printed support-free.I also did not need a brim, but you could put it on for safety since the parts are pretty narrow and the ends of the lightbar-parts could potentially lift from the bed.&nbsp;Rest of the print-settings in 1.75 PLA with 0.4 nozzle:<figure class="table" style="height:244.469px;width:714px;"><table style="border:1px double var(--input-border);"><tbody><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;vertical-align:top;">layer height</td><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;vertical-align:top;">0.2mm</td></tr><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;vertical-align:top;">walls</td><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;vertical-align:top;">2</td></tr><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;vertical-align:top;">top shell layers</td><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;vertical-align:top;">2</td></tr><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;vertical-align:top;">bottom shell layers</td><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;vertical-align:top;">2</td></tr><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;vertical-align:top;">infill</td><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;vertical-align:top;">15% grid</td></tr></tbody></table></figure>&nbsp;

Ultra slim monitor light

Rix Originals

mcmaven

This is a 3D-printed model of a triple-axis tourbillon, which is based on the tourbillon in a Jacob and Co. Twin Turbo Furious watch. A tourbillon is a mechanism employed to counteract the effects of gravity within a watch. This intricate model includes an escape wheel, triple-axis outer frame, and a base with an integrated motor. It functions on the same fundamental principles as a traditional watch tourbillon.&nbsp;With precise assembly and calibration of the escape wheel, spring, and base drive gear, this tourbillon can smoothly rotate in three axes and maintain accurate timekeeping. The provided print settings in the Triple-axis Tourbillon Model for Kit-007.3mf file are already customized to ensure that all screw holes are clear and ready for assembly.&nbsp;Printed plastic ‘screws’ are printed to scale and used as caps to cover the steel screws that actually hold it together.<a target="_blank" href="https://youtu.be/2-7S2i6AUyM" rel="nofollow noopener">Here </a>is a real-time video of the tourbillion in action.&nbsp;Note: There are two different designs defined for the Tourbillon: the 3MF version and the STL version.&nbsp;The 3MF (Triple-axis Tourbillon Model for Kit-007.3mf file) version was designed specifically to work with Bambu printers and the Bambu slicer, and uses the Triple-axis Tourbillon Model Hardware Kit motor to drive it. It is a slightly modified version of the original STL tourbillon version. To build the 3MF version you only need to order the <a target="_blank" href="https://shrsl.com/4d484" rel="nofollow noopener">Triple-axis Tourbillon Model Hardware Kit</a>, which provides all the non-printed parts (screws, bearings, shafts cut to length, motor, etc.) needed to build a complete model. <a target="_blank" href="https://www.youtube.com/watch?v=HRNbihDXNwE" rel="nofollow noopener">Here </a>is a video of assembling the 3MF version with the Bambu 007 hardware kit. Note that some of the sections in the Furious Build Notes PDF file below also apply to assembling the 3MF version, with the primary difference being the construction and components of the Base and the drive mechanism.&nbsp;The STL (Raw Model Files) version is a set od files that was designed to work with any printer or slicer. It also uses a more complex Arduino controlled stepper motor mechanism to drive it. To build the STL version you can order a kit of all the non-printed parts <a target="_blank" href="https://www.makerrx.com/collections/projectkits/products/twin-turbo-furious-tourbillon-kit" rel="nofollow noopener">here</a>, otherwise you will need to order the parts listed in the Furious Build Notes PDF instructions individually. If you order the STL version of the hardware kit or buy the parts yourself, you will need to program the firmware into the Arduino before it will work. The Furious Build Notes PDF file below, describes the assembly process for the STL version. For some of the larger parts, ‘full’ (e.g., Base Outer Ring.STL) and ‘split’ versions (Base Outer Ring a.STL and Base Outer Ring b.STL) of the same part are included. The ‘full’ parts require at least a 220x220 bed for printing. The ‘split’ parts may be printed separately on a diagonal on a smaller bed, then glued together to form the larger part.&nbsp;The following filaments can be used to create a model that looks like the pictured gold, silver, copper and black version:<ul><li><a target="_blank" href="https://shrsl.com/4cim5" rel="nofollow noopener">PLA Silk Gold</a></li><li><a target="_blank" href="https://shrsl.com/4cim4" rel="nofollow noopener">PLA Silk Silver</a></li><li><a target="_blank" href="https://shrsl.com/4cim3" rel="nofollow noopener">PLA Silk Copper</a></li><li><a target="_blank" href="https://shrsl.com/4cim2" rel="nofollow noopener">PLA Basic Black</a></li></ul>Here is a video of the construction of the 007 kit. And some sections in the Furious Build Notes.PDF file may be useful for constructing the 007 kit.<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=bHEU9rnnu88"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/bHEU9rnnu88" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;Disclaimer: This model is part of the Creator Program, When you purchase the Triple-axis Tourbillon Model Components Kit through the links below, creators may earn an affiliate commission as a reward of their work. (The creator program is currently in the trial phase. The application is not yet open to public.)&nbsp;The Hardware Kit for the Triple-axis Tourbillon Model for Kit-007.3mf file can be found here: <a target="_blank" href="https://shrsl.com/4d484" rel="nofollow noopener">Triple-axis Tourbillon Model Hardware Kit</a><a target="_blank" href="https://shrsl.com/4cfzj" rel="nofollow noopener">.</a>

TT Furious Tourbillon

clock

DBR-it

<h3> LightArt</h3>A piece of art that lights up on the wall which each Cube can be a different color or all the same using the WLED app endless possibilities you will need several components And sometime and some patienceThe other SVG files if you have a CNC machine or you could router out by hand use the file for measurements <h4>Video Link</h4><a href="https://youtube.com/shorts/9uXfr4IdvhQ?feature=share" rel="nofollow">https://youtube.com/shorts/9uXfr4IdvhQ?feature=share</a><h4> Things needed</h4><ol><li><a href="https://amzn.to/3OTOC77" rel="nofollow">Power supply</a></li><li><a href="https://amzn.to/3Uebv5Y" rel="nofollow">Esp32</a></li><li><a href="https://amzn.to/3OGWdW8" rel="nofollow">Wire</a></li><li>Soldering skills <a href="https://amzn.to/3gF7TfK" rel="nofollow">soldering iron </a></li><li>router</li><li>Wood</li><li>Nail gun </li><li><a href="https://amzn.to/3OINymb" rel="nofollow">LED strips 2812</a></li><li>Wood glue</li><li>The obvious 3D printer</li><li><a href="https://amzn.to/3OGN2VH" rel="nofollow">Hot glue gun</a> Glue Parts together</li></ol>&nbsp;

LightArt

Lighting

Chaosdrucker

LED Leiste für WL2812b Spielerei mit WLED.Infos dazu unter : <a href="https://github.com/Aircoookie/WLED/wiki" rel="nofollow">https://github.com/Aircoookie/WLED/wiki</a> oder: <a href="https://github.com/JvPeek/" rel="nofollow">https://github.com/JvPeek/</a><h3> Print Settings</h3>Printer Brand:PrusaPrinter: <div>I3 MK3S</div>Rafts:NoSupports: <div>Yes</div>Resolution:0.3Infill: <div>10</div> Filament: Redline / geeetech PLA black / white Notes: <div>Diffusor stehen drucken im Vasenmodus auf 0.2. LED Schiene liegend mit 0.3 möglich.Die Löcher an der Seite noch einmal leicht weiten und ein Stück Filament reinstecken damit mehrere Teile zusammengesteckt werden können.WS2812b: https://amzn.to/3q3B3UI Wemos D1 mini: https://amzn.to/38tXqgm*Affiliate Links</div>Category: Art

LED Schiene mit Diffusor für WS2812b (für 10mm Breite)

Keylight

Mick23

Hi, here a little model of a Benchy.It print Flat with nos supports, If the slicer says it need supports, Ignore that it need supports.&nbsp;When its printed, draw imaginaire dot lines on the benchy paint.Its between these right dotlines you need to heat with a lighter underneath, back and forth until the temperature is just above 65 degrees.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/144958/2023-10-29_84c0142564525.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/144958/2023-10-29_2c74131012b53.jpg">&nbsp;Now you can fold it over and push on it to a corner of a table or shelf.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/144958/2023-10-29_bad51dff6a066.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/144958/2023-10-29_e8499a47f1d43.jpg">&nbsp;When it is cool down, you can heat between the other imaginary dot lines.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/144958/2023-10-29_67767c001d3d4.jpg">&nbsp;And repeat the previous steps&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/144958/2023-10-29_63166aad2147b.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/144958/2023-10-29_afd3c56859e46.jpg">&nbsp;If you have any problem , let me know&nbsp;Look also my cube paint https://makerworld.com/nl/models/55104#profileId-56614&nbsp;&nbsp;&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/144958/2023-11-01_8492330af006.jpg">And please if you like it , share it and print it!!!! And show me your pictures. and rate the print profile please Like it if you want and follow me for other items. Comments welcome&nbsp;I added also a print profile in mirror mode if you want

Benchy paint No support

Benchys

dewgenenny

Love wine? Love 3d printing? &nbsp;Then this is the print for you! The Infinite Wine Rack is a modular wine rack that you can print and grow to your hearts desire. &nbsp;The design is made up of three parts only - <ul><li>Hexagonal Ring - two needed per wine bottle, one for front and one for back</li><li>Inside Connector - needed for joining two rings together and extending the wine rack</li><li>Outside Connector - needed for joining two rings together but not extending</li></ul>The parts pressure fit together so that you most likely don't need to glue. At least, I haven't had to but YMMV.&nbsp;If you print this and it's useful to you I'd love you to share a make and photo :) &nbsp;&nbsp;

The Infinite Wine Rack 

Home

Hamstah

Update 25/11/2023: I've added stronger versions of all 3 sizes. Some people were having difficulty printing the original model, so I've increased the height and thickened the links to give the model quite a bit more strength. The trade off is that the model is slightly less flexible, but definitely still a lot of fun to play with. Hope that helps!--&nbsp;Dual sided triangle “chain mail” style fabric. Fun to play with! I recommend printing the tester first, as it is really important that the filament adheres well to the bed for a good print. If one triangle gets knocked off the bed, it can ruin the print (though I have had success if one or two get knocked loose).&nbsp;The easier model to print (and more fun in my opinion) is the 120mm square, but I included a 250mm wide strip for those that want more of it.&nbsp;I also highly recommend using a plastic scraper to remove the print from the bed, and you won't be able to get the fabric to release by bending the bed, and pulling on the fabric will snap the joints.&nbsp;Consider changing filament on the middle layer to get a second colour on the flip side of the fabric!&nbsp;Warning: The 250mm wide version of the fabric takes a very long time to slice!

macropad

Showcase

Games

Gridfinity

Tools

Kids

Figurines

Study

Art

Games

Rix Originals

clock

Lighting

Keylight

Benchys

Home

Fun prints

possible upgrades