A1/A1 mini Cable elastic conduit

Search models, users, collections, and posts

ShapeX

3D Printer>3D Printer Accessories

IP Report

Print Profile(12)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

PLA，Small-sized，0.2mm layer, 2 walls, 15% infill

Designer

28 min

1 plate

4.9(5.9 k)

PLA，Large-sized，0.2mm layer, 2 walls, 15% infill

Designer

39 min

1 plate

4.9(2.5 k)

A1 mini - reliable print - both version (plates)

1.2 h

2 plates

4.9(420)

2% wider for a better fit

37 min

1 plate

4.9(478)

Click to see more

Open in Bambu Studio

Boost

15830

42129

10541

4.4 k

96.4 k

81.6 k

Released

Description

The cable flexible guide tube designed for A1 and A1 mini can lift the sagging cable to prevent cable interference with the tool head movement.

Short ones are installed on the line at one end of the toolhead, while long ones are installed on the line at one end of the X-axis

Installation steps:

As shown in the figure, align the opening of the cable guide tube with the cable, and pay attention to the bottom of the cable guide tube should be above the cable base.
Insert the cable along the opening into the cable guide tube.
Pull the cable guide tube down as a whole until the device is inserted into the cable base.

为A1与A1 mini设计的线缆弹性导向装置，可以抬高下垂的线缆，防止线缆干扰工具头运动。

短的安装在工具头一端的线上，长的安装在X轴一端的线上

安装步骤：

1.如图所示，将该装置开口与线缆对齐，请注意装置底部需在线缆底座的上面。

2.将线缆沿开口塞入装置中。

3.将装置整体向下拉，直至装置插入线缆底座。

a1 mini

cable

Conduits

Comment & Rating (10541)

@junz

Fits my A1 pretty well at 102.5%.

@spotkiller

Boosted

Also for me. Thanks for testing.

@user_2171639277

This worked. Thanks again.

@user_1452999207

ah I wish I saw that earlier 😀

@Cyberox

Print Profile

PLA，Large-sized，0.2mm layer, 2 walls, 15% infill

A bit too tight to fit the cable. Good print

Show original

@Teknomi

yeh I had the same problem, the cable will just not go in fully

(Edited)

@deepz

same issue, I think the new A1 that was released after recall might have little thicker wire, not to sure but I tried to put this on the wire and it was very tight and pinching it so I decided not to use them. anyone else?

(Edited)

@T4Zx13

Replying to @Teknomi :

same, no way its fitting over the cable on mine. far too tight. I wonder if it were scaled up a few percent?

(Edited)

@Marcus_70

The print profile is no longer public

These worked perfect. I added some clips I designed with piano wire.

@obnaes

I was going to do the same. Which size did you use? I was looking at the 16 gauge

(Edited)

@chinacat911

Could you share your designed clip? I understand that 2 or 3 filament strands could replace the piano wire. Could you modify your clip design to accommodate 3 filament strands? Thank you

(Edited)

Show original

@Anticamper1985

Print Profile

PLA，Small-sized，0.2mm layer, 2 walls, 15% infill

perfect fit, thanks for sharing

@Mitch_does

Boosted

Print Profile

PLA，Large-sized，0.2mm layer, 2 walls, 15% infill

Quick print and does the job perfectly

@Eray0

Print Profile

PETG - Object Skippable - Print by Object

perfect

@Cerebralpanic

Print Profile

PLA，Small-sized，0.2mm layer, 2 walls, 15% infill

looks good. The time between the last layer print and the head returning to home seemed a little long. The print turned out fine though

@user_1671996892

did it fit without resize?

@Cerebralpanic

Replying to @user_1671996892 :

Hi. Yes it fit snuggly on each of the bottom of the cables. I'm doing another print currently, after I have installed the conduits, and they are holding fast.

@user_1671996892

Replying to @Cerebralpanic :

thank you for the quick reply printed and works awesome I used petg

@Zeusfpv

Print Profile

2% wider for a better fit

@benchybuilder67

bro you need to clean your printer right now

(Edited)

@Zeusfpv

Replying to @benchybuilder67 :

🤣🤣🤣 so true! it's still recovering from the move😅

Show original

@Enol3D

Boosted

Print Profile

Toolhead, same dim with x axis. morecontactsurfacemorestable

Highly practical, may require occasional readjustment if bending occurs

Show original

@Synkt

Print Profile

Toolhead, same dim with x axis. morecontactsurfacemorestable

Exactly as advertised

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.