HexScraper - Printbed scraper

HexScraper - Printbed scraper

Boost
32
72
54

Print Profile(1)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1

PLA 0.12mm layer, 2 walls, 15% infill
PLA 0.12mm layer, 2 walls, 15% infill
Designer
1.1 h
1 plate
4.9(49)

Boost
32
72
54
2
390
328
Released

Description

Perfect for scraping prints off your build plate, as well as your other scraping-needs. Should be printed with .15 or smaller layer height to make the edge sharp enough to slide under your prints.

 

Printing in PLA is possible, however PETG is recommended to add additional strength.

Comment & Rating (54)

Please fill in your opinion
(0/5000)

Print Profile
PLA 0.12mm layer, 2 walls, 15% infill
Came out really nice! had a small amount of stringing but I think that was more due to my filament being old rather than the profile. i think this is a better scraper than some of the others offered on MakerWorld with it being stronger and les prone to the edge chipping.
(Edited)
The designer has replied
0
Reply
Thanks for the review. I see you rated 4 stars - is there something I can improve with the profile? Regarding the stringing: try drying the filament. Take the original box, poke a few holes in it, heat your bed to 40°C and put the filament in the upside down box in there (spool touches the printbed directly). Leave for 6 hours, then turn the spool around and leave for 6 more. Should fix it.
0
Reply
Replying to @steelcroissant :
Hi bud, I don't nor.ally give 5 stars to be honest as I feel that there is always room for improvement. as for the filament drying, I have a Sunly dryer but in the instance of this particular filament, it is just very old so the stringing was expected with a few other artifacts. I do like your scraper a lot so please do not take the 4 stars personal! getting 5 stars for everything in life stifle further development and improvement. Best of the new year to you...
0
Reply
Print Profile
PLA 0.12mm layer, 2 walls, 15% infill
Top , belle qualité mais la lame n'est pas assez fine au bout . Enfin mon ancien fichiers scraper était mieux
0
Reply
Print Profile
PLA 0.12mm layer, 2 walls, 15% infill
Printed nicely. I might print a scaled down version as well as it's quite large for what I need.
0
Reply
Print Profile
PLA 0.12mm layer, 2 walls, 15% infill
nice
0
Reply
Print Profile
PLA 0.12mm layer, 2 walls, 15% infill
0
Reply
Print Profile
PLA 0.12mm layer, 2 walls, 15% infill
Made out of PLA+ turned out awesome!
0
Reply
Print Profile
PLA 0.12mm layer, 2 walls, 15% infill
simply the best scrapper for me
0
Reply
Print Profile
PLA 0.12mm layer, 2 walls, 15% infill
I printed in ABS with no issues
0
Reply
Print Profile
PLA 0.12mm layer, 2 walls, 15% infill
I don't know if I'm doing something wrong. Printed with Bambu Lab PETG and it printed just fine. But I'm literally unable to remove any prints from the plate with printed scrapers (not just this one - also the small one). I feel like the "tip" is to big/high. I just can't get under the prints. I even have the feeling that the prints damage the blade (slight bends in the blade). Still giving 4 stars because this might just be my fault :)
0
Reply
good print 👌👌👌
0
Reply