IKEA SKADIS Modular System by HX8 - Free 3D Print Model

Search models, users, collections, and posts

HX8 3D Design

Household>Other House Models

IP Report

Print Profile(7)

All

X1 Carbon

P1S

P1P

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

A1 mini

Components, 0.2mm layer, 4 walls, 15% infill

Designer

6.1 h

3 plates

4.9(204)

A Single Stand, 240x240mm, 0.2mm layer, 4 walls, 15% infill

Designer

6.1 h

2 plates

5.0(117)

Pegboards, 9 sizes, 0.2mm layer, 4 walls, 15% infill

Designer

19.3 h

9 plates

5.0(97)

Desk Clamp, 0.2mm layer, 4 walls, 15% infill

Designer

4.2 h

1 plate

5.0(30)

Click to see more

Open in Bambu Studio

Boost

3802

12128

571

369

7.4 k

4.1 k

Released

Description

My new project on Crowdfunding (LINK)

Boost Me (for free)

This is an on-going project, with be keep updated.

IKEA SKADIS MODULAR SYSTEM

A modular pegboard for desktop and more, this is an on-going project, more sizes and components will keep coming out, you can also leave in the comments for what you wish to have.

V1.0:

9 sizes of pegboards, steps with 240, 160 and 80mm
some basic components
I used the clips from @LineArcLine on printables

IMPORTANT NOTE: ALL FLAT CONNECTORS NEED TO BE USED IN FRONT AND BACK OF THE BOARDS!

WICHTIGER HINWEIS: ALLE FLACHVERBINDER MÜSSEN AN DER VORDER- UND RÜCKSEITE DER PLATTEN VERWENDET WERDEN!

重要提示：每个连接件需要打印2份，正反面同时使用！

Notes:

I tested on X1C and A1 Mini, with BBL PLA Basic and Matte filaments, other filaments have not been tested, please calibrate before print to avoid print failure.
slow down the first layer, I setup to 15mm/s for the first layer in my 3mf profile.
disable the cooling for the first 3 layers to enhance the adhesive is recommended.
I cut out a little piece on 1 corner of 240x240mm board, to avoid the reserved space on X/P series printers, in this case you do not need to change the print volume setting in bambu studio or manually block the cutter pusher.

Enjoy your print!

Check out my latest design:

Comment & Rating (571)

@metalface25

I am using this for a non-standard application. I have a dog that loves to climb the cat tree to get at the food. this wall keeps him down. I am new at 3D printing, but this model came out perfectly without me doing anything other than hitting print. Only add I might change (if I knew how) would be to add a corner bracket that switches the locking pin position. This would allow for more configuration.

@user_3271597713

thanks for the idea

@70sGamer

Print Profile

A Single Stand, 240x240mm, 0.2mm layer, 4 walls, 15% infill

An excellent design

Show original

@user_2601769663

Boosted

Wow – this is absolutely brilliant! Would it be possible for you to share the STL or STEP file, or any other printable format?

(Edited)

@gjb123

Replying to @user_2601769663 :

Just change the top and bottom layers to 0 in the slicer, and select gyroid infill. They didn't edit the STL or STEP file. It was done entirely in the slicer.

(Edited)

@user_1907110964

Where can I get such panels that few branches use

Show original

@kubusiaasty

Boosted

Print Profile

Pegboards, 9 sizes, 0.2mm layer, 4 walls, 15% infill

amazing! this was the best base for my work setup. everything is organized, no mess with cables on desk and it is very handy and takes minimum space :)

@digital_tara

Boosted

Print Profile

Components, 0.2mm layer, 4 walls, 15% infill

These are great! I'm really excited to use these for displays and table gifts at an event I'm going to. They work well for combining the various sizes of boards. I do have two suggestions/requests: I wish there was an angled connector and base at a wider angle (like halfway between the angle that's there and 180º/flat), so that I could connect three larger panels together and it not feel too closed up. Also, the angled base and the regular base aren't the same height from the table surface, so mixing them together doesn't work very well.

@wgshoppe

Agreed! Not sure why the angled base and regular base are different heights.

(Edited)

@Diego_CO3

Boosted

Print Profile

Components, 0.2mm layer, 4 walls, 15% infill

I would have preferred the components to be on separate plates instead they are all on one plate

Show original

@RainbowWizard

you can choose which objects to print on each plate

(Edited)

@RIRE

1 click society

(Edited)

@ZackAttackWack

Boosted

Print Profile

A Single Stand, 240x240mm, 0.2mm layer, 4 walls, 15% infill

Works great! it's way stronger then I anticipated, and I can hold some really heavy stuff. (Drawer is not from this)

@Paopaolalola

I adore that drawer! Could you tell me the source of the design? Thank you!

Show original

@Dray

Print Profile

Pegboards, 9 sizes, 0.2mm layer, 4 walls, 15% infill

Printed well in Petg-cf and Pet-g

The profile uploader has replied

@HX83D

thanks for your support!

@pr49matic

I love this modular Skadis kit but had trouble turning the locking pegs, so I made a tool that applies equal force on the entire turning "handle" of the pegs for easier turning/locking in place.

@colorfox

Boosted

Print Profile

Pegboards, 9 sizes, 0.2mm layer, 4 walls, 15% infill

Yes - it's even prettier in silk! 👌🏻 Really pleased with this one.

@zzc21th

Very nice, saved a lot of desktop space

The designer has replied

Show original

@HX83D

Thanks for the support I didn't realize so many domestic friends were on the global site

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Light Weight SKADIS IKEA

Gabb.99

18.4 k

8.2 k

IKEA Skadis modular pegboard

AdamKozakGrafika

7.4 k

2.9 k

IKEA Skadis

AU3D

82.9 k

18.7 k

Ikea Skadis Hooks

Marc Elbichon

24.8 k

6.3 k