Pontoon Rail System - Bracket - Free 3D Print Model

Search models, users, collections, and posts

kingmokex86

Hobby & DIY>Sport & Outdoors

IP Report

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.14mm layer, 3 walls, 30% infill

Designer

3.3 h

1 plate

4.7(18)

Open in Bambu Studio

Boost

159

395

606

324

Released

Description

Boost Me (for free)

If you liked the print please help me create more by dropping a boost :) thanks.

This bracket clamps onto a standard 1.25" pontoon railing and provides a mounting surface for the other attachments.

Caddy/Organizer Attachment:

https://makerworld.com/en/models/1433455

Rod Holder Attachment:

https://makerworld.com/en/models/750498

Drink Holder Attachment:

https://makerworld.com/en/models/750487

Dry Box Attachment:

https://makerworld.com/en/models/1318304

Comment & Rating (28)

@joshai

Print Profile

0.14mm layer, 3 walls, 30% infill

I had several failed attempts just like a couple of other commenters. The issue is more than likely their own fault, it was mine as well. i had the exact same issue. I keep my filaments dry and dry them before printing if they aren't already in my creality space pi4 dryers. This bracket is the only thing I have had issues with while printing PETG. I needed to slow down my print. The only successful prints I had at first were when i put it on half speed/quiet, during the night since I didn't care when it finished. I didn't think about that at first. I normally always use bambu petg basic profile for all my petg filaments I have. I was using comgrow, which is a great filament, but apparently on this bracket is has to be slowed down big time, I kept it around 50mm/s max speed, yeah it was a little slow, but that was the issue. I used this same filament on 2 little cubby boxes, 2 rod holders and the cup holders and ran it under the normal bambu settings with no issues.

(Edited)

@user_402435798

Failed twice on an A1 Mini - gets to the same point in printing and begins stringing out. (Picture attached)

The designer has replied

@kingmokex86

Not sure… I’ve only printed it on an X1C. you could try slowing the speed down and adding supports.

@user_3970760738

Print Profile

0.14mm layer, 3 walls, 30% infill

you need to ensure you have supports or it will not print, the print turned out perfect

(Edited)

@BluSkymaker

Boosted

Print Profile

0.14mm layer, 3 walls, 30% infill

perfect fit works great with the other options

@Sgt_Sold

This is awesome! is there a way to not have the under screw? I just bought a sun chaser and the siding goes all the way up

The designer has replied

@Sgt_Sold

I just realized that there could be a foot added to the screw to make it like a compression type thing.

@kingmokex86

Thanks! I couldn’t get the rod holder attachment hold tight enough without that screw, but the drink holder attachment may still work for you. Happy printing!

@Sgt_Sold

Replying to @kingmokex86 :

I am only level 4 so I can not respond to your message. I was thinking if widen the width of the clamp and move the screw up a little so it touches the rail. You could then add a foot with a rubber backing to the screw. ------------------------- I : I I :<====I====[] I : I I I I I I

@user_275935402

Have you considered a hook option? I was looking at this on printables: https://www.printables.com/model/530741-pontoon-boat-rail-hooks But it would be more useful to install this rail system and then be able to swap between hooks, cupholders, etc. as needed (if it's not something you're interested in then I can try my hand at CAD - appreciate you including the original file here)

@ChatChad

Print Profile

0.14mm layer, 3 walls, 30% infill

This worked great on my scissor lift as the railing is the same size. Easy print, tight fit so it won't move. Thanks!

@Reddog1970

Boosted

need the clamps for one inch pontoon rails

@BaverPrint

Print Profile

0.14mm layer, 3 walls, 30% infill

Very nice

@Kanely

Boosted

Print Profile

0.14mm layer, 3 walls, 30% infill

works great , will have to tweak it alittle to fit on a pier cart rail

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.