AMS Lite / Molex P4 Connector (Male + Female) - Free 3D Print Model

Search models, users, collections, and posts

3D Printer>3D Printer Accessories

IP Report

Print Profile(1)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.08mm layer, 2 walls, 100% infill

Designer

39 min

2 plates

4.5(28)

Open in Bambu Studio

Boost

136

289

458

262

Released

Description

AMS Lite connector. This usable part is now printable with a 0.4 nozzle. Can provide power to 5V electronics.

This can also be used as a standard P4 (4-pin) Molex Connector.

My intention and use for this modification was to wire up a 5v LED strip or a ESP32 to the AMS Lite port on my A1 Mini that would show status indications alongside the use of HomeAssistant & Octo-anywhere. This replicates similar functionality to that of the BLLED project.

You'll see in one of the photos of the model, I have cut off a portion of a dupont jumper wire to use as the connective material.

Boost Me (for free)

If you enjoy or put this print to good use, please leave a review and consider this for a BOOST! 😊

Please reach out with any questions in regards to printing and/or the model itself. Electronics and Engineering advice should come from elsewhere.

If you choose not to jerry-rig with wire or jumpers, proper connections can be found here:

Comment & Rating (43)

@Makermax101

Print Profile

0.08mm layer, 2 walls, 100% infill

Printed with a 0.2 mm nozzle Back piece broke during use

@Astr0_Man1

Boosted

Print Profile

0.08mm layer, 2 walls, 100% infill

very nice, came out better than expected

@dclabs

Print Profile

0.08mm layer, 2 walls, 100% infill

Strength Issue:Model looks nice, however with 0.4mm nozzle its not possible to make the piece thin enough. The ends break inside the port and its very hard to take them out without damaging the port. If you have 0.2mm nozzle you can try though.

@arraariatu

I understand you state you cannot provide electronics commentary, however, since you are certain that 5V objects can be connected, I understood that port delivers 24V. I have an ESP32 to connect, but I fear damaging it

The designer has replied

Show original

@jemma

I used a buck converter to step down to 5v

@swixbla

Replying to @jemma :

Does the ams lite port have an 24 v output

@user_400947310

great

@user_588104784

Boosted

Print Profile

0.08mm layer, 2 walls, 100% infill

male model is not correct. but for so small print its no matter. I made it for 12v led

@gabb4sauruzz

Print Profile

0.08mm layer, 2 walls, 100% infill

@user_2849676782

You can’t be serious.

@Mr.Murphy

Why does it look like it's made of mud? I suggest you check your print settings. Even the ender 3 printers from 7 years ago print better.

The designer has replied

@jemma

apologies if you had any trouble. the novelty of this particular profile is that it will produce an object that WORKS with a 0.4mm nozzle. you would ABSOLUTELY get a much prettier product if using a 0.2mm nozzle.

@nightswan

Replying to @jemma :

he was talking about print quality... yeah I'd try drying your filament lol

@heavydutyorca

please please please print this in flame retardant abs. this is otherwise a massive fire hazard.

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.