25mm pegboard hooks and boxes - Free 3D Print Model

Search models, users, collections, and posts

Remixed by

ImaRH 3D

Tools>Organizers

IP Report

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.24mm layer, 3 walls, 25% infill

Designer

14 h

8 plates

4.8(111)

Open in Bambu Studio

Boost

690

2643

122

3.2 k

1.8 k

Released

Description

This is a remix of pegboard tools from https://makerworld.com/en/@Penguin_holic.

Link to original model: https://makerworld.com/en/models/489263#profileId-408307

Added low baskets:

125x70
200x100
225x100
250x100
250x100 with holes for tools

with a front edge height just below 20 mm and a wall thickness of 2.4 mm.

Printed in normal mode (not a vase) with a layer height of .24 to save time.

Also added a file with clips:
peg_pin_baseB+v3.stl - author's original file with clips
new_peg_pin_naseB+v3 more tight for 5.8mm hole pegboard - new file for 5.5 mm hole boards

Thanks to the author for the step files!

Comment & Rating (122)

@Requinic

Boosted

Print Profile

0.24mm layer, 3 walls, 25% infill

The print turned out great. I only needed the shelf with all the holes. Since I have 1 inch pegboard, I had to scale the shelf width to 25.4mm/25mm or 1.016%. I also increased the width and height of the bracket by the same amount to match and fit the vertical 1 inch spacing. These three small changes were all I needed. I have a variety of screwdrivers and pliers that I want to store, so I may end up recreating this shelf by making one with small holes and slots for screwdrivers and another with bigger slots for pliers. Thank you for sharing these models.

The profile uploader has replied

@krokus57

Great idea with scale! I wanted to make several versions of other shelves, but the author forbade remixes by a license agreement.

(Edited)

@blwnblue

I wish I read this comment 3 days ago... I'm brand new to 3d printing and I printed this out of ABS... it warped JUST a bit and I thought that's why it didn't line up... sooo.. I printed it again..perfect... still didn't fit... last night I had the idea of a resize... so I measured I far I was off.. exactly 5mm.. so I enlarged the shelf to 255mm... 1mm shy of the bed max.. woke up this morning to tell everyone bc it fit perfect and I absolutely love these shelves.. Now here you are with the solution I've been needing had I only read the comments ... LOL!!! Also I was worried bc I didn't enlarge the pegs as then they'd have been too big...they slide in just as tight as designed even on the the 255mm shelf!

(Edited)

@user_2216783251

Boosted

Print Profile

0.24mm layer, 3 walls, 25% infill

These are perfect for the traditional and original peg board.

@JJM68

Print Profile

0.24mm layer, 3 walls, 25% infill

Excellent design and excellent print. I needed something to hold my mini torch on my peg board, and this worked perfectly!

@WhatChelleIMake

Print Profile

0.24mm layer, 3 walls, 25% infill

Had to resize the plate for it to fit my pegboard, but ultimately did fit and works well.

@NurseAudrey34

Boosted

Print Profile

0.24mm layer, 3 walls, 25% infill

I made it smaller to print on an A1 mini. I cut a middle section out and merged it back together. I got lucky the pegs matched up with my pegboard!

@user_2906733058

Print Profile

0.24mm layer, 3 walls, 25% infill

clean print

@bopboppop

Print Profile

0.24mm layer, 3 walls, 25% infill

works super well and holds tons of weight, I personally had to screw it into my wall because I am not using a pegboard but a skadis board instead and it works just fine.