Samsung Galaxy S22 case (basic, for magsafe and for cards) - Free 3D Print Model

Search models, users, collections, and posts

nyx_nk

Tools>Gadgets

IP Report

Print Profile(5)

All

P1P

X1 Carbon

X1E

P1S

H2D

A1 mini

H2D Pro

H2S

P2S

H2C

X2D

A2L

BASIC

Designer

1.6 h

1 plate

4.7(113)

FOR MAGSAFE RING (automatic pause at layer 5)

Designer

1.8 h

1 plate

5.0(4)

FOR CARDS

Designer

1.3 h

1 plate

4.3(18)

RIGID VERSION (PETG+TPU for H2D) - Magsafe

Designer

2.2 h

1 plate

Click to see more

Open in Bambu Studio

Boost

289

578

177

2.3 k

1.4 k

Released

Description

3 versions of Samsung Galaxy S22's case.

Basic
For Magsafe ring (you have to pause printing after layer 5 for 0.2 mm printing and insert metal ring - https://amzn.to/44DidrA)
For credit/transport card

I printed the case in TPU (90A/40D) without support on carbon-look plate on Bambulab P1P

Comment & Rating (177)

@MFDesigns3D

Print Profile

BASIC

fits perfectly

@user_1531384513

Boosted

How did you get these stars?

@MFDesigns3D

Replying to @user_1531384513 :

With the effects build plate. https://ca.store.bambulab.com/products/bambu-3d-effect-sheets-combo-with-plate

@user_1531384513

Boosted

Replying to @MFDesigns3D :

thanks mate!

(Edited)

@krishgup1

Print Profile

BASIC

really clean print perfect fit. looks great with this translucent red filament.

@HerrTankwart

Boosted

What filament have you used? I like this red!

@krishgup1

Replying to @HerrTankwart :

it's Amazon basics red tpu

(Edited)

@HerrTankwart

Boosted

Replying to @krishgup1 :

Thanks alot! I saw your answer and ordered instantly :-D

@Alu01

Print Profile

BASIC

printed in pla. looks good but due to lack of flexibility had to pressfit my Phone, which damaged the case a bit. buttons in the side not usable. NOT creator's fault and was expected. this was a testprint. will probably buy and try TPU next time. i guess TPU95a is recommended over TPU85a?

@Rylan31814

ya tpu 95a is best for phone cases.

@HotFix

Boosted

Print Profile

FOR MAGSAFE RING (automatic pause at layer 5)

I discovered this awesome model right as the D ring on my cheap cell phone case broke. I got a mag safe system (not sure what else to call it) and put the ring that is normally glued to the phone inside the print. https://www.amazon.com/dp/B0CYPL59TP I put the sticker side of the O down which means the filament had nothing to grab on to as it was printing. Luckily enough managed to stick that it sealed it in, and who cares what the inside looks like. Thank you for sharing with the community!

@JUSTXXL

Print Profile

BASIC

It fits perfectly

Show original

@burgui

Print Profile

BASIC

so cool, i wasnt expectingthe model to be this good

@user_363859933

Printed with TPU 95A HF fillament. Maybe I lack some knowledge...

@CalvinSlaven

Print Profile

BASIC

I see how it working looks like it would work great but definitely do not advise using normal pla you should definitely go with the TPU for way better results the back also doesn't look to good and I'm not sure why that is but I would assume it is because of the adhesion or does something to do with my rather than this print profile

@juniorx32g

It came out great, I really liked it. Printed with Elegoo TPU 95A red. I've added a 1mm extra layer to the back of the case, so the cameras are better protected (see screenshot attached). Most important with TPU I think (besides filament calibration): Lower speeds (screenshot attached)

(Edited)