Samsung Galaxy S24+ (plus) Voronoi case v2 - Free 3D Print Model

Search models, users, collections, and posts

ThesBer

Hobby & DIY>Electronics

IP Report

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

Voronoi 0.2mm layer, 2 walls, 15% infill

Designer

1.7 h

1 plate

4.6(18)

Open in Bambu Studio

Boost

184

605

331

Released

Description

Content has been automatically translated.

Show original

This is my second Samsung Galaxy S24+ (plus) Voronoi case, version 2

No support is required in the slicer settings :-)

The green components depicted serve as supports for effortless printing and must be removed subsequently Removal ease varies depending on the material and printer employed

I utilize TPU filament, 95A shore hardness, with slicer settings of 220 °C nozzle and 50 °C bed temperature For optimal TPU printing, ensure the filament is desiccated

See also version 1 --> https://makerworld.com/en/models/591443
and a new Halloween version 3 --> https://makerworld.com/de/models/643155

Boost Me (for free)

If you appreciate my work, please consider boosting this model

Downloads, likes, makes, and ⭐⭐⭐⭐⭐ ratings are always welcome!

Happy Printing
Toni

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Dies ist meine zweite Samsung Galaxy S24+ (Plus) Voronoi - Hülle Version 2

In den Slicer Einstellungen ist keine Unterstützung erforderlich :-)

Die grünen Teile im Bild dienen lediglich als Stützen zum einfachen Drucken und müssen anschließend entfernt werden Das Entfernen kann je nach Material und Drucker einfach oder schwierig sein

Ich benutzte Filament TPU härte 95A und Slicer Temperaturen -> Düse: 220 °C, Bed: 50 °C Für einen guten TPU-Druck sollte das Filament trocken sein

Siehe auch Version 1 --> https://makerworld.com/en/models/591443
und neue Halloween version 3 --> https://makerworld.com/de/models/643155

Viel Spaß beim Drucken
Toni

Comment & Rating (36)

@freshexpenses

Boosted

Print Profile

Voronoi 0.2mm layer, 2 walls, 15% infill

nice print.

The profile uploader has replied

@Toni_ThesBer

It looks nice. Thanks. I recommend using a hot air dryer to remove the stringing. For light colors, only hold the filament on it for a very short time (at high temperatures) so that it doesn't change color :-)

@Cocodone

Print Profile

Voronoi 0.2mm layer, 2 walls, 15% infill

Printed using PLA Matte because I need a quick case while waiting for my ordered one to arrive. I do not recommend using PLA, it is too stiff. It needs a lot of force to put on and off, and the camera holes do not fully fit on. But it did work great as a temporary case.

The profile uploader has replied

@Toni_ThesBer

Thanks for the information. The model was designed for flexible TPU filament. It may also work partly with PETG, which is a bit more flexible than PLA :-)

(Edited)

@Mr_Wiktor789

Print Profile

Voronoi 0.2mm layer, 2 walls, 15% infill

I made it out of pla and it was perfect size

The profile uploader has replied

@Toni_ThesBer

Thank you :-)

@majki47

Print Profile

Voronoi 0.2mm layer, 2 walls, 15% infill

Served until real case arrived, lacks strength around power and volume buttons

The profile uploader has replied

@Toni_ThesBer

Thanks :-)

@Schelleboom

Boosted

Print Profile

Voronoi 0.2mm layer, 2 walls, 15% infill

Good and clean

The profile uploader has replied

Show original

@Toni_ThesBer

Thanks :-)

@Cowaselon

Print Profile

Voronoi 0.2mm layer, 2 walls, 15% infill

Printed perfectly

The profile uploader has replied

@Toni_ThesBer

Thank you :-)

@NikoD

Print Profile

Voronoi 0.2mm layer, 2 walls, 15% infill

Perfect print

The profile uploader has replied

@Toni_ThesBer

Thank you :-)

@axelsti

Boosted

Print Profile

Voronoi 0.2mm layer, 2 walls, 15% infill

the cover part where the volume is located should be improved

The profile uploader has replied

Show original

@Toni_ThesBer

Thanks... i'll take a look at it.

@SqiLLoWs

unfortunately the cover does not fit it is a bit too small, the edges are lifting! we printed the model in TPU as usual, we tried a second time but unfortunately the second print was also too small for the S24 FE

The designer has replied

Show original

@Toni_ThesBer

Hello, it is also not intended for the FE. Since I didn't have the FE, I could never create one for it. The two models S24 and S24 FE have different dimensions. Best regards

(Edited)

Show original

@user_1741814997

Print Profile

Voronoi 0.2mm layer, 2 walls, 15% infill

printing with TPU was stringy

The profile uploader has replied

@Toni_ThesBer

Hello, just three stars. The model can't be blamed if your filament is stringing. Many others have printed it in TPU successfully. Did you dry your TPU filament beforehand?