Cyclone Passthrough Toy [EXTRA Long] - Free 3D Print Model

Search models, users, collections, and posts

Dotted Lines

Toys & Games>Other Toys & Games

IP Report

GIF

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

Creator Recommended: Slow Speeds, 0.2mm layer, 2 walls

Designer

12.4 h

2 plates

4.8(12)

Open in Bambu Studio

Boost

140

292

339

138

Released

Description

Your favorite impossible fidget toy… now SIGNIFICANTLY LONGER.

Boost Me (for free)

Please consider boosting & liking if you enjoy the model, I would love to create and share more with the community.

Impossible EXTRA Long Passthrough Toy

How long is it?

This file was designed to be as long as possible. It is the tallest possible dimension for Bambu printers (250mm).

Surprisingly easy to print
Compatible with Bambu X1, P1 & A1 Printer
I recommend a dual or tri-color filament for beautiful color changes

Assembly

Put the big stick inside the other big stick
If you have stringing, gently use a blow torch or heat gun to remove
Parts will loosen up over time

Print Settings (recommended):

Avoid Crossing walls
Slow speeds
Redice infill retraction: no
Cyclone file: 0% infill
Large brim around outer walls
Take extra care when printing on an A1 or other bed slinger (increase brim, lower speeds)

For commercial rights: https://www.patreon.com/DottedLines

toy

passthrough

impossible

impossible passthrough

Comment & Rating (19)

@user_2503664597

Print Profile

Creator Recommended: Slow Speeds, 0.2mm layer, 2 walls

Printed exceptionally well. I sometimes have some issues with these pass through models, but this was perfect.

@user_1980835390

Welp, no-go for me. The center part printed all the way, but I left the outside running overnight and found this is morning. Would supports help? I test-fitted the outside part that DID print and it slides OK on the bottom part of of the center section, but it gets really tight about two inches from the top of the center and won't move further. I assume it's because of the wobble induced by the moving print bed. This is a long print and I am a newbe so I think I'll wait a bit before trying again!

@drshelby

Print Profile

Creator Recommended: Slow Speeds, 0.2mm layer, 2 walls

Love love

@BriFrenzy

Boosted

Easy print. Action was a little tight, but loosened with time.

@Joemaster240

Boosted

Gonna print this on my new A1! I love things like this.

The designer has replied

@dottedlines

Thanks for the boost! Hope you enjoy it

@UGRZ

Very good model The inner part tipped over just before the end (Bambu P2S) I reprinted it with glue on the build plate and then it worked perfectly

(Edited)

Show original

@lfrumberg

Printed nicely, BUT got stuck half way through when I tried it out. So, it was a fail after 20+ hours of printing.

@geekdadkevin

Print Profile

Creator Recommended: Slow Speeds, 0.2mm layer, 2 walls

think it was a recent firmware issue but didn't fit for me a not willing to try it again but looks awesome

@stang.92

Boosted

Love this toy!

@user_2201833948

Print Profile

Creator Recommended: Slow Speeds, 0.2mm layer, 2 walls

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.