Modular Skadis Container | Regular - Free 3D Print Model

Search models, users, collections, and posts

AU3D

Tools>Organizers

IP Report

Print Profile(2)

All

P1P

P1S

X1 Carbon

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

2 Variants | 100x80x80mm | 0.16mm layer, 2 walls, 15% infill

Designer

7.6 h

2 plates

4.9(113)

for A1 Mini | 2 Variants | 100x80x80mm

Designer

9.2 h

2 plates

5.0(33)

Open in Bambu Studio

Boost

420

1454

168

1.2 k

640

Released

Description

As I am running out of space on my Skadis wall, I needed a new approach to attach more accessories. To use the space more efficiently, I created a basic container with integrated Skadis holes, allowing additional accessories to be attached, thereby freeing up space on the board itself. The inner dimensions are approximately 100x80x80mm (WxDxH), and there are two variants: one with a four-way divider and one without. If you have suggestions for alternative dimensions, please let me know in the comments. The container is very sturdy, adhering to the original board's design specifications with a thickness of approximately 5mm.

Installation

The container can be mounted on the Skadis board like any other accessory. For a more permanent installation, I recommend using my Double Lock plug (in 9.5 or 10mm) to prevent the container from detaching accidentally.

If possible, attach any additional accessories before mounting the container to the Skadis board to avoid unnecessary stress on the hooks. Note that the layer lines of the container create more friction than the original IKEA Skadis boards, making it a bit harder to mount and unmount accessories.

Related Models

Modular Skadis Container | Medium

Skadis Collection

I am constantly developing more IKEA Skadis attachments. Check out my

Boost Me (for free)

Hey friends! I’m doing this purely as a passion project in the little free time I have (juggling two full-time jobs and a family). If you have questions, requests, or feedback, feel free to shoot me a DM — I’d love to hear from you when I get the chance. Boosts and support mean the world and help keep this hobby alive — thank you so much!

Comment & Rating (168)

@Tokolozi

Boosted

Print Profile

2 Variants | 100x80x80mm | 0.16mm layer, 2 walls, 15% infill

handy design, maybe a slightly taller one would be great too.

(Edited)

The profile uploader has replied

@AU3D

Could you provide the specific dimensions you have in mind?

@Tokolozi

Boosted

Replying to @AU3D :

Nothing specific, but maybe just one row of 'skadis holes' higher :)

@AU3D

Replying to @Tokolozi :

Sure, I will tag you when its done so you get notified.

(Edited)

@rlogiacco

Print Profile

2 Variants | 100x80x80mm | 0.16mm layer, 2 walls, 15% infill

a bit hard to push in the skadis slots, but it also gives some confidence against seeing it sliding out by accident. a very nice print, and a good addition for my “wall of shame” 😁

The profile uploader has replied

@AU3D

Looks like a normal wall to me ;-)

(Edited)

@crypt3d

Boosted

Print Profile

2 Variants | 100x80x80mm | 0.16mm layer, 2 walls, 15% infill

great box

(Edited)

The profile uploader has replied

@AU3D

Thank you very much for the make and boost!

(Edited)

@Printin3d

Print Profile

2 Variants | 100x80x80mm | 0.16mm layer, 2 walls, 15% infill

Great idea and perfect execution. Printed perfectly first time despite running out of filament half way through, Appreciate what you do.

The profile uploader has replied

@AU3D

Thank you for the kind words!

@BCO85

Print Profile

2 Variants | 100x80x80mm | 0.16mm layer, 2 walls, 15% infill

The hooks are 2 tenths too wide. Can be solved with sanding. Thanks for sharing 👍🏻

The profile uploader has replied

Show original

@AU3D

Have you measured the corresponding width? My hooks are 4.7 mm wide at their widest point in the model and should therefore easily fit through the 5 mm wide Skadis opening.

Show original

@emc2cube

Boosted

Print Profile

for A1 Mini | 2 Variants | 100x80x80mm

Great finish (Bambulab Matte White PLA, "silent" / 50% speed). Perfect size to store hardware store sanding sponges.

@JonanSeeley

Boosted

Print Profile

for A1 Mini | 2 Variants | 100x80x80mm

Great idea and great print! Perfect for holders that need lots of vertical room above them like the angle finder holder. Thank you for all your skadis models!

@emiliegr

Boosted

Print Profile

for A1 Mini | 2 Variants | 100x80x80mm

Great design! Helps to optimize space on your Skadis! 🙌

@ArCy

Print Profile

2 Variants | 100x80x80mm | 0.16mm layer, 2 walls, 15% infill

Prints well but I have a few problems. First if there wouldn't be the center hook but just 4 hooks on the back, I could hang it between two Skadis plates or on the bottom edge of one. Also, the thickness is exactly 5mm, whereas the Skadis has ~5,15mm. This results in all extension being without any friction fit (see gap in photo), leaving a possibility to take off holders too when grabbing the tools on them.

The profile uploader has replied

@AU3D

@ArCy First off, thank you for your feedback. I'm happy to address your points as follows: I'm glad to hear that you had no issues printing this model. Please note that your rating should reflect the print profile rather than the model itself. I agree that the delta hook might limit the options slightly. However, since I'm unsure about the load placed on the container, I wanted to add extra stability. It's much easier to remove the hook yourself than to add one later. In Bambu Studio, it's a simple process: - Select the container. - Click "Split to Parts". - In the objects list, select the hook you want to remove (e.g., ....stl_3). - Press "Delete" to remove the part/hook. - Done! I will see if I can adjust my approach in the future to cover more scenarios. Regarding the thickness, Skadis boards do not have a uniform thickness; they vary between 4.8 and 5.1mm depending on the model (black, white, natural, painted, or unpainted). It seems you are using the white board, which is the thickest variant. Even the creator of the T-Clip system, which you use for your attachments, mentions the need for different clips based on board thickness. Given this variability, if the pliers holder shown in your image sits loose on this container, it would likely sit loose on black and natural boards as well (~4.8mm). This is an issue that can only be resolved by the attachment's creator. As for the friction of attachments, it's important to note that there is no standard for the hooks, so stating that "all" attachments won't have any friction seems a bit odd to me. I can guarantee that all my 200+ Skadis models have plenty of friction with this container. And for the ones I have no control over, I created the Skadis Lock Plug (https://makerworld.com/en/models/92747) and the Double Lock Plug (https://makerworld.com/en/models/505811).

(Edited)

@Firefighter2008

Print Profile

for A1 Mini | 2 Variants | 100x80x80mm

Amazing idea, prints perfect

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.